Temperature to Energy Conversion: How It Works
- Hot side in kelvin
- K
- Result
- Cold side in kelvin
- K
- Result
- Hot side temperature
- 300 °C
- You entered
Temperature to energy conversion means using a temperature difference to produce useful energy, typically electricity, through devices like thermoelectric generators (TEGs), heat engines, or thermophotovoltaic cells. You input a hot side and a cold side temperature, and the calculator below estimates the maximum theoretical efficiency (Carnot efficiency) of such a conversion, along with the corresponding energy fraction you could extract. It also shows how much heat energy is available in a given mass of a substance when its temperature changes.
Formula
The fundamental limit for converting heat into work is given by the Carnot efficiency:
η_carnot = 1 − T_cold / T_hot
where:
- η_carnot is the maximum possible efficiency (as a fraction, 0 to 1).
- T_hot is the absolute temperature of the hot reservoir (in kelvin).
- T_cold is the absolute temperature of the cold reservoir (in kelvin).
Because the formula uses absolute temperatures, you must convert Celsius to kelvin by adding 273.15. The calculator does that automatically.
Worked Example
Using the default values: hot side = 300 °C, cold side = 25 °C.
- Convert to kelvin: T_hot = 300 + 273.15 = 573.15 K; T_cold = 25 + 273.15 = 298.15 K.
- Compute the ratio: 298.15 / 573.15 ≈ 0.5202.
- Subtract from 1: 1 − 0.5202 = 0.4798.
- Convert to percentage: 0.4798 × 100 = 47.98%.
The calculator shows 47.98% as the maximum theoretical efficiency. Real devices achieve far less, typically 5–15% for thermoelectric generators, because of material limitations and heat losses.
Background: Why Temperature Differences Matter
Energy cannot be extracted from a single temperature alone. The second law of thermodynamics states that heat flows spontaneously from hot to cold, and only the fraction of that heat that passes through a conversion device can be turned into work. The larger the temperature difference, the higher the theoretical ceiling. This is why power plants use high-pressure steam (hot) and cooling towers (cold), and why thermoelectric generators are placed on hot pipes with fins on the cool side.
How Thermoelectric Generators (TEGs) Work
A thermoelectric generator uses the Seebeck effect: when two different conductive materials are joined at two junctions kept at different temperatures, a voltage develops. The voltage is proportional to the temperature difference and the material’s Seebeck coefficient. In practice, TEGs are made of semiconductor couples (p-type and n-type) connected electrically in series and thermally in parallel. They have no moving parts, which makes them reliable for remote sensors, space probes, and waste-heat recovery. Their efficiency is usually below 10% because the materials also conduct heat, reducing the temperature gradient.
Real-World Applications and Limits
- Spacecraft power: Radioisotope thermoelectric generators (RTGs) convert heat from radioactive decay into electricity for missions far from the Sun.
- Waste heat recovery: TEGs on car exhaust pipes or industrial chimneys capture some heat that would otherwise be lost.
- Remote sensors: Small TEGs power wireless sensors in pipelines or on engines using the temperature difference between the pipe and ambient air.
- Portable generators: Camping stoves with TEGs can charge phones, but output is small (a few watts).
The main limit is efficiency: even with a 300 °C difference, the maximum is about 48%, but real TEGs rarely exceed 10%. Cost per watt is also high compared to solar panels or batteries.
Common Misconceptions
One common mistake is assuming that a small temperature difference (say 10 °C) can power a household. In reality, the Carnot efficiency for 10 °C difference near room temperature is only about 3.3%, and a practical device would be far less. Another misconception is that “energy conversion” means creating energy; it does not—it only transforms heat into work, and the rest is rejected to the cold side. Also, the calculator gives the maximum possible efficiency, not the actual output of any specific device.
How to Use the Calculator
Enter the hot side temperature (the heat source) and the cold side temperature (the heat sink) in degrees Celsius. The calculator returns the Carnot efficiency as a percentage. Use this to estimate the upper bound of any heat engine or thermoelectric generator. For example, if you have a geothermal source at 150 °C and ambient air at 20 °C, the maximum efficiency is about 30.7%. Real systems will be lower, so treat the result as a screening tool, not a design specification.
Safety and Practical Considerations
When working with hot surfaces, always use proper insulation and avoid contact with skin. High-temperature heat sources (above 100 °C) can cause severe burns. If you are building a thermoelectric generator, ensure the hot side does not exceed the material’s maximum operating temperature (often 150–300 °C for commercial TEGs). Also, the cold side must be actively cooled to maintain the temperature difference; otherwise, the efficiency drops quickly. Always follow the manufacturer’s guidelines for any device you use.
Frequently Asked Questions
Can I convert temperature directly to electricity? Yes, using a thermoelectric generator (Seebeck effect) or a heat engine. The temperature difference drives electrons or a working fluid, producing electricity. The efficiency is limited by the Carnot formula.
What is the best temperature difference for a TEG? Larger differences give higher efficiency, but each TEG has a maximum hot-side temperature. A practical range is 100–300 °C hot side with ambient cooling (20–30 °C cold side). Beyond that, materials degrade.
Why is my thermoelectric generator output so low? Real TEGs have efficiencies of 5–10% of the Carnot limit due to electrical resistance, thermal conduction through the legs, and imperfect contacts. Check that the cold side is actually cool and that the hot side is well attached to the heat source.
Does the calculator work for any heat engine? Yes, the Carnot efficiency applies to any heat engine (steam turbine, Stirling engine, etc.) as the maximum theoretical limit. Real engines have additional losses, so the actual efficiency will be lower.
What is the difference between temperature and heat? Temperature measures the average kinetic energy of particles, while heat is the total energy transferred due to a temperature difference. You need heat flow, not just high temperature, to generate power.
Can I use this calculator to size a TEG for my project? It gives the theoretical maximum, but you must also know the heat flow available (watts) and the TEG’s efficiency curve. Multiply the heat flow by the Carnot efficiency and then by a realistic factor (0.05–0.15) to estimate output.
Related
Formula used
in t_hot | Hot side temperature | °C | 300 | 0 in t_cold | Cold side temperature | °C | 25 | 0 out carnot_eff | Max efficiency (Carnot) | % | (1 - (t_cold + 273.15) / (t_hot + 273.15)) * 100 | 2 out kelvin_hot | Hot side in kelvin | K | t_hot + 273.15 | 2 out kelvin_cold | Cold side in kelvin | K | t_cold + 273.15 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.