ThisCalculator

Everyday

Dropped Pixel 2 in Water? Fix Steps

Updated · Standard formula, shown below

If you dropped your Pixel 2 in water, the immediate fix is to power it off, dry the outside with a soft cloth, and place it in a well-ventilated area for at least 48 hours before attempting to charge or turn it on. The Pixel 2 has an IP67 rating, meaning it can survive submersion in up to 1 meter of freshwater for 30 minutes, but water damage is not covered by warranty and can still occur, especially in saltwater, chlorinated water, or if the seals are worn.

Understanding the IP67 Rating

The Pixel 2’s IP67 rating is a standardized measure of dust and water resistance. The “6” means it is completely dust-tight, and the “7” means it can be immersed in freshwater up to 1 meter (about 3.3 feet) for up to 30 minutes. This rating is based on laboratory tests with clean, still water at room temperature. Real-world conditions often differ: a drop in a pool, a toilet, or the ocean introduces chemicals, bacteria, or pressure that can overwhelm the seals. Also, the rating assumes the device is in pristine condition; scratches, drops, or prior repairs can compromise the adhesive and gaskets that keep water out.

Immediate Steps After the Drop

Act quickly but calmly. The goal is to minimize water ingress and prevent short circuits.

  1. Retrieve the phone and turn it off immediately if it is still on. Press and hold the power button, then select “Power off.”
  2. Remove the SIM card tray to allow water to escape and air to enter.
  3. Shake out excess water gently from the USB-C port, speaker grilles, and earpiece. Do not blow into them with your mouth, as moisture can be forced deeper.
  4. Dry the exterior with a soft, lint-free cloth or paper towel. Pay attention to seams and openings.
  5. Place the phone upright in a dry, well-ventilated area with the USB-C port facing down. A gentle fan can help airflow, but avoid direct heat.
  6. Do not charge or press buttons for at least 24–48 hours. Charging a wet phone can cause corrosion and short-circuit the logic board.

What NOT to Do

Many common “fixes” are myths that can cause more harm than good. Avoid these:

  • Do not use rice. Rice dust can get into the port and speakers, and it does not absorb moisture effectively from inside a sealed device. It also introduces starch that can corrode contacts.
  • Do not use a hairdryer or oven. Heat can melt internal adhesives, warp the chassis, and damage the battery.
  • Do not use compressed air. The force can push water deeper into the device.
  • Do not move the phone around excessively. Shaking can spread water to components that were still dry.
  • Do not plug in a charger to “test” if it works. Even if the port looks dry, moisture can remain.

Drying Methods That Actually Work

Silica gel packets (the kind that come in shoe boxes) are far more effective than rice. Place the phone in a sealed container with several packets for 48–72 hours. Silica gel absorbs moisture without releasing dust. If you don’t have silica gel, leave the phone in a dry room with air circulation. A low-power fan (not a hairdryer) can help evaporate moisture. Some people use a vacuum cleaner on low suction near the openings, but this is risky if the phone has loose components. The safest method is patience: leave it alone for at least two full days in a dry environment.

When to Try Turning It On

After 48 hours, inspect the USB-C port and speakers with a flashlight. If they appear completely dry, you can attempt to turn the phone on. If it boots, back up any data immediately. If it does not turn on, connect it to a charger and wait 15 minutes. If it still shows no signs of life, the battery or logic board may be damaged. Do not attempt to open the phone yourself unless you have experience; the internal components are delicate and the battery is glued.

Common Problems After Water Exposure

Even if the phone turns on, you may notice issues:

  • Muffled or crackling speaker – Water may be trapped in the speaker mesh. Play a low-frequency tone or use the “water eject” feature on some apps (though this is not officially supported). Often, the sound clears after a day or two.
  • Charging issues – Corrosion on the charging port can prevent charging. The phone may say “moisture detected” – this is a safety feature that disables charging until the port is dry.
  • Screen discoloration or flickering – Water may have seeped into the display layers. This usually requires professional repair.
  • Camera fog – Condensation inside the camera lens. It may evaporate, but if it persists, the camera module needs replacement.

Professional Repair vs. Replacement

If the phone does not work after drying, you have two main options: take it to a professional repair service or replace the phone. Water damage is not covered by the standard warranty, but some credit cards offer purchase protection that may cover accidental damage within a certain period. Repair costs can vary widely; for a Pixel 2, a logic board repair or battery replacement may cost more than the phone’s current value. If you have important data that was not backed up, a professional data recovery service may be able to extract it, but this is expensive and not guaranteed. Before deciding, consider the phone’s age and condition – the Pixel 2 is now several years old, and replacement may be more cost-effective.

Prevention for the Future

To avoid this situation again, use a waterproof case if you are near water. The IP67 rating is not a guarantee, and cases provide an extra layer of protection. Also, check the condition of your phone’s seals: if you have had the screen replaced or the back removed, the water resistance is likely compromised. Avoid taking the phone into saunas, hot tubs, or saltwater environments. If you do get it wet, follow the same immediate steps – power off, dry, and wait.

Frequently Asked Questions

How long should I wait before charging my Pixel 2 after water exposure?
Wait at least 48 hours. Even if the port looks dry, moisture can remain in the internal connectors. Charging too early can cause corrosion and short-circuit the battery.

Can I use a hair dryer on low heat to dry the phone?
No. Hair dryers can push water deeper and the heat can damage internal components. Use silica gel packets or just leave the phone in a dry, ventilated area.

Is the Pixel 2 waterproof in saltwater?
No. The IP67 rating is for freshwater only. Saltwater is highly corrosive and will damage the phone much faster. Rinse the phone with fresh water if it touches saltwater, then dry it as usual.

What does the “moisture detected” warning mean?
It means the charging port has moisture that could cause a short circuit. The phone deliberately disables charging to protect itself. Keep the phone in a dry area and try again after a few hours.

Will the water damage be covered by warranty?
No. Standard manufacturer warranties do not cover water damage. However, some credit card companies offer accidental damage protection if you purchased the phone with that card – check your card’s benefits.

Should I put the phone in rice?
No. Rice is not an effective desiccant and can introduce dust and starch into the phone. Use silica gel packets or simply air dry.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.