Standard Temperature and Pressure in PSI?
The calculator for this page is switched off while it is checked. The formula is below, and the worked example in the article shows how to use it by hand.
Standard temperature and pressure (STP) in psi is 14.696 pounds per square inch (psi) for pressure, with temperature defined as 0°C (32°F). This is the standard value used in chemistry and physics for gas calculations, though other standard conditions exist for different industries.
Formula
The calculator above lets you compare a given pressure and temperature to the STP baseline. The pressure ratio is simply:
Pressure ratio = P / 14.696
where P is the pressure in psi. The temperature conversion uses the standard formula:
°C = (°F − 32) × 5/9
These formulas help you quickly see how far a set of conditions deviates from STP, which is useful when checking gas law calculations or equipment ratings.
Worked Example
Using the default values from the calculator:
- Pressure = 14.696 psi
- Temperature = 32°F
Pressure ratio = 14.696 / 14.696 = 1.000 (to three decimals)
Temperature in °C = (32 − 32) × 5/9 = 0°C
So at STP, the pressure ratio is exactly 1, and the temperature is 0°C. This confirms the calculator’s output.
What Does Standard Temperature and Pressure Mean?
Standard temperature and pressure is a reference set of conditions used to report gas volumes and other properties that depend on temperature and pressure. The most widely used definition comes from the International Union of Pure and Applied Chemistry (IUPAC), which sets STP as 0°C (273.15 K) and 100 kPa (1 bar). However, in the United States and in many engineering contexts, the older definition of 0°C and 1 atm (14.696 psi) is still common.
Because gases expand when heated and compress when pressurized, their volume changes with conditions. To compare measurements taken at different times or places, scientists and engineers normalize them to a standard set of conditions. This is why you see STP on gas cylinders, flow meters, and in chemistry problems.
Why 14.696 psi?
The value 14.696 psi comes from the definition of one standard atmosphere (atm). An atmosphere was originally based on the average pressure of Earth’s atmosphere at sea level. Over time, it was precisely defined as 101,325 pascals. Converting that to pounds per square inch gives:
101,325 Pa × (1 psi / 6,894.757 Pa) = 14.6959 psi
Most references round this to 14.696 psi or sometimes 14.7 psi for quick calculations. The difference between 14.696 and 14.7 is about 0.03%, which is negligible in most practical work.
Other Standard Conditions
STP is not the only reference set. You may also encounter:
- Standard Ambient Temperature and Pressure (SATP): 25°C (298.15 K) and 100 kPa (14.504 psi). Used in some chemistry contexts.
- Normal Temperature and Pressure (NTP): 20°C (293.15 K) and 1 atm (14.696 psi). Often used in engineering and gas industry.
- Standard Conditions for Gas Volume (SCF): In the US natural gas industry, often 60°F and 14.73 psi.
Always check which standard your source uses. Mixing them up can lead to errors of several percent in gas volume calculations.
Common Mistakes and Misconceptions
One common mistake is confusing absolute pressure with gauge pressure. STP is always given in absolute pressure. A tire gauge reads 0 psi at atmospheric pressure, so a gauge reading of 14.7 psi actually corresponds to 29.4 psi absolute. When comparing to STP, make sure you use absolute pressure.
Another error is using the wrong temperature scale. STP uses absolute temperature in kelvins for gas law calculations. If you use Celsius or Fahrenheit without converting, your results will be wrong. The calculator above helps with the conversion, but for gas law problems you need to convert to kelvins: K = °C + 273.15.
Also, note that STP is a reference, not a physical law. Real gases deviate slightly from ideal behavior at STP, but for most purposes the ideal gas law works well.
How to Use STP in Calculations
STP is most often used in the ideal gas law:
PV = nRT
where P is pressure, V is volume, n is the number of moles, R is the gas constant, and T is temperature. At STP, one mole of an ideal gas occupies 22.414 liters (using 1 atm) or 22.711 liters (using 1 bar). This molar volume is handy for converting between mass and volume of gases.
For example, to find the volume of 2 moles of oxygen at STP, you multiply: 2 mol × 22.414 L/mol = 44.828 L. If you are using the bar-based STP, the volume would be 45.422 L. The difference is about 1.3%, so it matters in precise work.
Frequently Asked Questions
Is STP the same as standard conditions for gases?
Not always. STP specifically means 0°C and 1 atm (or 1 bar). Standard conditions for gases can vary by industry, such as 15°C or 60°F. Always confirm the definition used in your field.
What is the difference between STP and NTP?
STP uses 0°C (273.15 K), while NTP (Normal Temperature and Pressure) uses 20°C (293.15 K). Both use 1 atm (14.696 psi) for pressure. NTP is more common in engineering and gas flow measurements.
Does STP apply to liquids and solids?
No, STP is primarily for gases. Liquids and solids have negligible compressibility, so their volumes don’t change much with pressure or temperature. For those, you usually don’t need a standard reference.
How do I convert psi to atm?
To convert psi to atm, divide by 14.696. For example, 29.392 psi ÷ 14.696 = 2.000 atm. Conversely, multiply atm by 14.696 to get psi.
Why do some sources use 14.7 psi instead of 14.696?
14.7 is a rounded value for quick mental math. The exact conversion from 101,325 Pa gives 14.6959 psi, which is often rounded to 14.696 for more precision. For most calculations, 14.7 is close enough.
Can I use STP for real gases like carbon dioxide?
Yes, but with caution. Real gases deviate from ideal behavior, especially at high pressures or low temperatures. At STP, most common gases behave nearly ideally, but for very accurate work you may need to use a real gas equation like van der Waals.
Related
Formula used
in p | Pressure | psi | 14.696 | 0 in t | Temperature | °F | 32 | 0 out ratio | Pressure ratio | (p / 14.696) | 3 out temp_c | Temperature in °C | °C | (t - 32) * 5 / 9 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.