Standard Pressure and Temperature Aviation: ISA Explained
The calculator for this page is switched off while it is checked. The formula is below, and the worked example in the article shows how to use it by hand.
Standard pressure and temperature in aviation refer to the International Standard Atmosphere (ISA) model: a sea-level pressure of 29.92 inches of mercury (1013.25 hectopascals) and a sea-level temperature of 15°C (59°F), with temperature decreasing by about 2°C per 1,000 feet of altitude up to 36,000 feet. These values are not real weather; they are a fixed reference used to calibrate altimeters, compare aircraft performance, and standardize flight planning across the world.
Formula
The ISA model defines a linear temperature lapse rate in the troposphere (the lowest layer of the atmosphere, up to 36,089 feet or 11 km). The temperature at any altitude is:
T = T₀ − L × h
- T = temperature at altitude (°C)
- T₀ = sea-level standard temperature = 15°C (59°F)
- L = lapse rate = 1.98°C per 1,000 ft (approximately 2°C per 1,000 ft, or 6.5°C per km)
- h = altitude (feet above mean sea level)
Pressure follows a more complex exponential relation based on the hydrostatic equation and the ideal gas law. For altitudes up to 36,000 ft, the standard pressure is:
P = P₀ × (1 − 2.25577 × 10⁻⁵ × h)^5.25588
- P = pressure at altitude (hPa or inHg)
- P₀ = sea-level standard pressure = 1013.25 hPa (29.92 inHg)
- h = altitude (feet)
The exponent 5.25588 comes from the ratio of gravitational acceleration to the product of the gas constant and the lapse rate. Above 36,000 feet, the temperature becomes constant at −56.5°C in the standard model, and the pressure formula changes accordingly.
Worked Example
Using the calculator defaults: altitude = 10,000 ft, temperature at that altitude = −15°C.
Step 1: Calculate ISA temperature at 10,000 ft.
ISA temp = 15 − 2 × (10,000 / 1,000) = 15 − 20 = −5°C.
Step 2: Find the temperature deviation.
Deviation = actual temp − ISA temp = −15 − (−5) = −10°C. So the air is 10°C colder than standard.
Step 3: Calculate standard pressure at 10,000 ft.
P = 1013.25 × (1 − 2.25577 × 10⁻⁵ × 10,000)^5.25588
= 1013.25 × (1 − 0.225577)^5.25588
= 1013.25 × (0.774423)^5.25588
≈ 1013.25 × 0.2616 ≈ 265.1 hPa (about 7.83 inHg).
So at 10,000 ft in the standard atmosphere, temperature is −5°C and pressure is about 265 hPa. The calculator shows the same results: ISA temp −5°C, deviation −10°C, standard pressure 265.1 hPa.
Why Aviation Uses a Standard Atmosphere
Aviation needs a common reference because pressure and temperature vary constantly with weather. If every pilot used the day’s actual pressure, altimeters would disagree and aircraft separation would be unsafe. The ISA solves this by defining one fixed set of values. Altimeters are built to read correctly when set to 29.92 inHg at sea level; when the actual pressure differs, pilots adjust the altimeter setting to the local value (QNH) so the altimeter shows true altitude above mean sea level.
The standard atmosphere also lets manufacturers publish performance charts that pilots can use anywhere. For example, a Cessna 172’s takeoff distance is listed for standard conditions; the pilot then applies corrections for temperature and pressure altitude. Without a baseline, every chart would need to be re-created for every weather condition.
How Temperature and Pressure Affect Aircraft Performance
Both temperature and pressure affect air density, which directly impacts lift, engine power, and propeller efficiency. Warmer air is less dense, so the same wing produces less lift, and the engine takes in less oxygen per volume. Higher altitude also reduces air density. The combined effect is captured by density altitude – the altitude at which the aircraft “feels” it is flying in the standard atmosphere.
- Hot day: Density altitude is higher than true altitude, so takeoff roll is longer and climb rate is lower.
- Cold day: Density altitude is lower, so performance improves.
- High pressure: Denser air improves performance; low pressure reduces it.
- Humidity: Water vapor is lighter than nitrogen and oxygen, so humid air is less dense – a small but measurable effect on performance.
Pilots calculate density altitude using the outside air temperature and pressure altitude. A common rule of thumb: for every 1°C above standard temperature, density altitude increases by about 120 feet. For example, at 5,000 ft pressure altitude on a 30°C day (ISA at 5,000 ft is 5°C), the deviation is +25°C, so density altitude ≈ 5,000 + (25 × 120) = 8,000 ft.
Common Mistakes and Misconceptions
One frequent error is confusing standard pressure with pressure altitude. Pressure altitude is the altitude read on an altimeter when set to 29.92 inHg. It is not the same as true altitude unless the actual sea-level pressure happens to be 29.92 inHg. For instance, if the local pressure is 30.20 inHg, the pressure altitude will be lower than the field elevation.
Another misconception is that the ISA temperature lapse rate is exactly 2°C per 1,000 ft. The official value is 1.98°C per 1,000 ft (6.5°C per km). Using 2°C is a common approximation that introduces a small error of only 0.02°C per 1,000 ft – negligible for most calculations.
Pilots also sometimes forget that the standard atmosphere extends only to 36,000 feet. Above that, the temperature is constant at −56.5°C in the standard model, so the lapse-rate formula no longer applies. The pressure formula also changes, using a different exponent and base.
How to Read the Calculator Results
The calculator gives three outputs: temperature deviation, ISA temperature at altitude, and standard pressure at altitude. The temperature deviation is the most useful for performance calculations – a negative deviation means colder than standard (better performance), positive means hotter (worse performance). The ISA temperature tells you what the standard temperature should be at that altitude, so you can compare it with the actual outside air temperature from a weather report or in-flight sensor. The standard pressure is the theoretical pressure in the standard atmosphere; it is not the actual pressure you would read on a barometer, but it is useful for understanding altimeter settings and for converting between pressure and altitude.
For example, if you are flying at 8,000 ft and the outside air temperature is 0°C, the calculator shows ISA temp = 15 − 16 = −1°C, deviation = +1°C. That means the air is slightly warmer than standard, so your density altitude will be a bit higher than 8,000 ft – about 8,120 ft using the 120 ft per °C rule.
Limitations of the ISA Model
The ISA is a simplified model, not a prediction of real weather. Real atmospheres often have temperature inversions (temperature increasing with altitude), which the ISA does not represent. The model also assumes dry air; humidity is not included. For high-altitude or high-temperature operations, the ISA may be less accurate, and more detailed models (like the U.S. Standard Atmosphere 1976) are used in engineering.
For everyday aviation, the ISA is accurate enough for performance planning and altimetry. It is the basis for all standard flight instruments and most regulatory definitions (e.g., “standard day” in aircraft manuals). It is also used in meteorology and aerospace engineering for comparing measurements.
Frequently Asked Questions
What is the difference between standard pressure and QNH?
Standard pressure (29.92 inHg or 1013.25 hPa) is a fixed reference value used for pressure altitude and flight above a transition altitude. QNH is the actual barometric pressure adjusted to mean sea level, which pilots set on their altimeter to read true altitude above sea level. When you set QNH, the altimeter shows field elevation on the ground; when you set 29.92, it shows pressure altitude.
Why is standard temperature 15°C and not 20°C?
The 15°C value was chosen as a representative average sea-level temperature for mid-latitudes, based on historical atmospheric data. It is a convenient round number that makes calculations easy, not a global average (which is about 14°C). The International Civil Aviation Organization (ICAO) adopted the ISA in the 1950s, and 15°C was already in use in earlier standard atmospheres.
Does the standard atmosphere apply above 36,000 feet?
No. The ISA defines the troposphere up to 36,089 feet (11 km) with a lapse rate of 1.98°C per 1,000 ft. Above that, in the stratosphere, the temperature is constant at −56.5°C up to about 65,000 feet. The pressure continues to decrease, but with a different formula. Most general aviation aircraft fly below 36,000 ft, so the tropospheric model is sufficient.
How does temperature deviation affect my takeoff distance?
Warmer-than-standard air reduces air density, so the engine produces less power and the wings generate less lift. This increases takeoff distance. As a rough rule, for every 1°C above standard, takeoff distance increases by about 1% for a typical light aircraft. For example, a 10°C deviation adds about 10% to the takeoff roll. Always consult the aircraft’s performance charts for precise figures.
What is the standard pressure in millibars?
Standard pressure is 1013.25 millibars (mb), which is the same as 1013.25 hectopascals (hPa). The hectopascal has replaced the millibar in most aviation weather reports, but they are numerically identical. In inches of mercury, it is 29.92 inHg.
Related
Formula used
in t | Temperature at altitude | °C | -15 | 0 in a | Altitude | ft | 10000 | 0 out dev | Temperature deviation from ISA | °C | t - (15 - 2 * a / 1000) | 2 out isa_temp | ISA temperature at altitude | °C | 15 - 2 * a / 1000 | 2 out std_press | Standard pressure at altitude | hPa | 1013.25 * (1 - 2.25577e-5 * a)^5.25588 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.