ThisCalculator

Everyday

PLA Creep: What Every 3D Printer Owner Needs to Know

Updated · Standard formula, shown below

Estimated creep strain 0.10 %
Temperature
22 °C
You entered
Load
5 MPa
You entered
Time
24 hours
You entered

PLA creep is the slow deformation of printed parts under constant pressure or heat, and every 3D printer owner needs to know that it can ruin functional prints even at room temperature. This article explains what creep is, why PLA is especially prone to it, how to test for it, and how to design around it.

Formula

The calculator estimates the percentage of creep strain (deformation) a PLA part might experience under a constant load. The formula is:

Estimated creep strain (%) = (Load / 50) × (1 + (Temperature − 20) / 50) × (Time / 24)^0.3

Where:

  • Load (MPa) – the constant stress applied to the part (typical tensile strength of PLA is 50–60 MPa, so use a fraction of that).
  • Temperature (°C) – the ambient temperature the part is exposed to. PLA’s glass transition is around 60°C, but creep becomes noticeable well below that.
  • Time (hours) – how long the load is applied. The exponent 0.3 reflects the typical power-law behavior of polymers under constant stress.

This is a simplified model for educational purposes. Real creep depends on exact material formulation, infill, print orientation, and humidity.

Worked Example

Using the default values: Temperature = 22°C, Load = 5 MPa, Time = 24 hours.

  1. Calculate the temperature factor: (22 − 20) / 50 = 0.04, so 1 + 0.04 = 1.04.
  2. Calculate the load factor: 5 / 50 = 0.1.
  3. Calculate the time factor: (24 / 24)^0.3 = 1^0.3 = 1.
  4. Multiply: 0.1 × 1.04 × 1 = 0.104, so the estimated strain is about 0.10%.

That means a 100 mm long part would deform by roughly 0.1 mm under those conditions. That may be negligible for a decorative piece but unacceptable for a precision bracket.

What Is Creep in 3D Printing?

Creep is the time-dependent deformation of a material under constant stress. When you leave a heavy object on a PLA shelf, the shelf slowly bends even if the stress is far below the material’s yield strength. Unlike brittle fracture, creep happens gradually and often goes unnoticed until the part has permanently warped.

All thermoplastics creep, but PLA is particularly susceptible because it has a relatively low glass transition temperature (around 60°C) and a tendency to soften even at moderate temperatures. A PLA part in a hot car (50°C) can lose a significant portion of its stiffness within hours.

Why PLA Creeps More Than Other Filaments

PLA is a stiff, brittle plastic at room temperature, but its molecular structure allows polymer chains to slide past each other when under load. The glass transition temperature (Tg) is the key: below Tg, the polymer is glassy and rigid; above Tg, it becomes rubbery and flexible. PLA’s Tg is about 60°C, but creep can start at temperatures well below that, especially if the stress is high.

Compare with PETG (Tg ~80°C) or ABS (Tg ~105°C): those materials have higher Tg values, so they resist creep better at elevated temperatures. However, even ABS will creep if the load is high enough and time is long enough. Nylon is even more prone to creep because it absorbs moisture and acts as a plasticizer.

How to Test for Creep in Your Own Prints

You don’t need advanced equipment to see creep. A simple test: print a cantilever beam (e.g., 100 mm long, 10 mm wide, 5 mm thick) and clamp it horizontally. Hang a known weight (say 500 g) from the free end. Measure the deflection immediately, then again after 24 hours, 48 hours, and a week. The increase in deflection is creep.

  • Use a dial indicator or a caliper to measure deflection.
  • Keep the temperature constant (avoid direct sunlight or drafts).
  • Try the same test with different infill percentages (20%, 50%, 100%) to see how infill affects creep.
  • Also test with parts printed in different orientations (flat vs. upright) because layer adhesion is weaker than solid material.

If the deflection keeps increasing over time, you’re seeing creep. If it stabilizes, the material may have reached a steady state.

Designing Parts to Resist Creep

You can’t eliminate creep, but you can minimize its effect:

  • Increase wall thickness and infill: more material means more load-bearing cross-section, reducing stress.
  • Use ribs or gussets to support high-stress areas.
  • Avoid sharp corners where stress concentrates; use fillets.
  • Print with 100% infill for structural parts, or at least use a grid or gyroid infill that distributes load well.
  • Orient the print so that layer lines are perpendicular to the main stress direction (i.e., load is along the layers, not pulling them apart).
  • Consider annealing PLA (heating it to 50-60°C for a while) to increase crystallinity and stiffness, though this can cause warping.

Remember that creep is time-dependent: a part that holds fine for a day may fail after a month. If the part is meant to last, design for a safety factor of at least 2-3 relative to the expected stress.

Common Misconceptions About PLA Creep

Misconception 1: “Creep only happens at high temperatures.” False. Creep happens at any temperature, just faster at higher temperatures. Even at 20°C, a PLA part under constant load will deform over time.

Misconception 2: “If it doesn’t break immediately, it’s safe.” Not true. Creep can cause sudden failure after hours or days, especially if the part is notched or has a defect.

Misconception 3: “Higher infill always stops creep.” Higher infill helps, but the outer walls and the quality of layer adhesion matter more. A part with 100% infill but poor layer bonding can still creep.

Misconception 4: “PLA is fine for structural parts because it’s stiff.” Stiffness (elastic modulus) is not the same as creep resistance. PLA is stiff initially, but it creeps more than PETG or ABS under sustained load.

Alternatives to PLA for Load-Bearing Parts

If your part will be under constant load or exposed to heat, consider these filaments:

  • PETG: Higher Tg, better creep resistance, and easier to print than ABS. Good for functional parts.
  • ABS/ASA: Higher Tg, but requires a heated bed and enclosure to avoid warping.
  • Nylon: Very tough and wear-resistant, but absorbs moisture and creeps more than PLA unless filled.
  • Polycarbonate: Excellent creep resistance and high Tg, but prints at very high temperatures and needs a hardened nozzle.
  • Carbon-fiber filled PLA or PETG: The fibers add stiffness and reduce creep, but they can wear brass nozzles.

For most hobbyists, PETG is a reasonable upgrade from PLA for functional parts. For industrial applications, you’d look at injection-molded parts or specialized engineering plastics.

Frequently Asked Questions

Does PLA creep at room temperature?

Yes, but very slowly. At 20°C, a lightly loaded PLA part may take months to show visible deformation. However, if the stress is high (near the yield strength), creep can be noticeable within days. The effect is accelerated by even moderate warmth (e.g., a sunny window).

Can I anneal PLA to reduce creep?

Annealing PLA (heating it to 50-60°C for 30-60 minutes, then cooling slowly) can increase crystallinity and stiffness, which may reduce creep. However, it can also cause shrinkage and warping, so test with a small part first. Annealed PLA still creeps more than PETG.

Is creep the same as warping?

No. Warping is a distortion that occurs during printing due to uneven cooling and shrinkage. Creep is a time-dependent deformation that occurs after printing, under load. Warping is a print defect; creep is a material property.

How do I know if my part will creep too much?

Use the calculator above to estimate strain. If the estimated strain is more than 1-2% for a functional part, it’s likely to cause problems. For precision parts, even 0.5% may be too much. Always test with a prototype under real conditions.

Can I fix a crept PLA part by re-printing?

Re-printing with the same material and design will give the same result. Instead, change the design (add ribs, more walls) or switch to a more creep-resistant filament. If the part is only slightly deformed, you might be able to reshape it with heat, but that’s risky and weakens the material.

Related

Formula used
in t | Temperature | °C | 22 | 0
in load | Load | MPa | 5 | 0
in hours | Time | hours | 24 | 0
out strain | Estimated creep strain | % | (load / 50) * (1 + (t - 20) / 50) * (hours / 24) ^ 0.3 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.