ThisCalculator

Everyday

Percentage Related by Error? Explained

Updated · Standard formula, shown below

Percentage change 20.00 %
Percentage error
20.00 %
Result
Original value
100
You entered
New value
120
You entered

This calculator works out a percentage change or error between two numbers, showing the relative difference as a percentage. You enter the original (or accepted) value and the new (or measured) value, and you get the percentage increase or decrease, or the percentage error. The result tells you how large the difference is compared with the starting value, which is useful for checking accuracy, tracking changes, or comparing estimates.

Formula

For percentage change (increase or decrease):

Percentage change = ((New value − Original value) / Original value) × 100

For percentage error (absolute relative difference):

Percentage error = (|New value − Original value| / |Original value|) × 100

Variables:

  • Original value – the starting or accepted value (no unit, any number).
  • New value – the later or measured value (same unit as original, but units cancel).
  • Percentage change – can be positive (increase) or negative (decrease).
  • Percentage error – always non‑negative, measures magnitude of difference.

Worked Example

Using the default values: original = 100, new = 120.

  1. Difference = 120 − 100 = 20
  2. Relative difference = 20 / 100 = 0.2
  3. Percentage change = 0.2 × 100 = 20%
  4. Percentage error = |20| / |100| × 100 = 20% (same here because the change is positive and original is positive)

So a change from 100 to 120 is a 20% increase, and the error (if 100 is the accepted value) is 20%.

When to Use Percentage Change vs. Percentage Error

Choose the right measure based on your situation:

  • Percentage change – use when tracking growth, decline, price changes, population changes, or any before/after comparison. It shows direction: positive means increase, negative means decrease.
  • Percentage error – use when comparing a measured or estimated value to a known or accepted value, like in science labs, engineering tolerances, or forecasting accuracy. It always shows magnitude, ignoring direction.

For example, if you expected 100 visitors and got 120, the error is 20% (you were 20% high). If you expected 120 and got 100, the error is still 20% (you were 20% low), but the percentage change would be −16.67%.

How to Read the Result

A positive percentage change means the new value is larger than the original; a negative means smaller. A percentage error of 0% means perfect agreement; the larger the error, the farther the new value is from the original, relative to the original’s size.

Context matters: a 5% error might be acceptable in one field and disastrous in another. Always compare the error to the tolerance or requirement of your task.

Common Mistakes and Pitfalls

  • Dividing by the wrong value – for percentage change, always divide by the original value, not the new one. For error, divide by the accepted value.
  • Ignoring the sign – percentage change can be negative; percentage error cannot. Mixing them up gives misleading results.
  • Unit mix‑ups – both values must be in the same unit. The percentage itself is unitless.
  • Zero original value – division by zero is undefined. If the original is 0, a percentage change cannot be calculated; you can only state the absolute difference.
  • Rounding too early – round only at the final step to keep accuracy.

Limits of the Formula

The percentage change formula assumes the original value is a meaningful baseline. If the original is very small (e.g., 0.001), a tiny absolute change becomes a huge percentage, which may be misleading. Also, percentage changes are not symmetric: a 50% increase followed by a 50% decrease does not return to the original value (e.g., 100 → 150 → 75). For such symmetric comparisons, use logarithms or relative difference with a different denominator.

For percentage error, the formula only works when the accepted value is non‑zero. In cases where the accepted value is zero, absolute error is used instead.

Frequently Asked Questions

What is the difference between percentage change and percentage error?

Percentage change shows the direction of change (increase or decrease) relative to the original value. Percentage error shows the magnitude of the difference relative to the accepted value, always as a positive number. Use change for trends, error for accuracy.

Can percentage change be negative?

Yes. If the new value is less than the original, the percentage change is negative, indicating a decrease. For example, a drop from 200 to 150 is a −25% change.

What if the original value is zero?

You cannot divide by zero, so percentage change and percentage error are undefined. In that case, report the absolute difference instead. For example, if the original is 0 and new is 5, the absolute increase is 5, but no percentage can be calculated.

Is a 10% error the same as a 10% change?

Not always. If the new value is higher than the original, both are the same (e.g., 100 to 110 gives 10% change and 10% error). But if the new value is lower, percentage change is negative (e.g., 100 to 90 gives −10% change) while error is still 10%.

How do I calculate percentage error when the accepted value is negative?

Use the absolute value of the accepted value in the denominator. For example, accepted = −50, measured = −40: difference = 10, |accepted| = 50, error = 20%. The sign of the accepted value does not affect the magnitude of the error.

Related

Formula used
in original | Original value | - | 100 | 0
in new | New value | - | 120 | 0
out change | Percentage change | % | ((new - original) / original) * 100 | 2
out error | Percentage error | % | (abs(new - original) / abs(original)) * 100 | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.