ThisCalculator

Everyday

Percentage of Error Equation & How to Use It

Updated · Standard formula, shown below

Percentage error 4.00 %
Absolute difference
2.00
Result
Accepted value
50
You entered
Measured value
48
You entered

This calculator works out the percentage error between an accepted or true value and an experimental or measured value. You enter the true value and the measured value, and it returns the percentage error, showing how far your measurement is from the accepted value as a percentage. The formula is simple: divide the absolute difference by the accepted value, then multiply by 100.

Formula

Percentage error (often called percent error) is calculated as:

Percentage Error = (|Measured Value − Accepted Value| ÷ Accepted Value) × 100%

Where:

  • Measured Value is the value you obtained from an experiment, observation, or estimate (same units as the accepted value).
  • Accepted Value is the true, theoretical, or reference value (same units as the measured value).
  • |…| means absolute value – you always take the positive difference, so the error is never negative.

The result is a percentage that tells you how large the error is relative to the true value. A smaller percentage means your measurement is closer to the accepted value.

Worked Example

Using the default values from the calculator: accepted value = 50, measured value = 48.

  1. Subtract the measured value from the accepted value: 48 − 50 = −2
  2. Take the absolute value: |−2| = 2
  3. Divide by the accepted value: 2 ÷ 50 = 0.04
  4. Multiply by 100 to get a percentage: 0.04 × 100 = 4%

So the percentage error is 4%. This matches the calculator’s output (rounded to two decimal places).

When to Use Percentage Error

Percentage error is used in science, engineering, statistics, and any field where you compare a measured or estimated value against a known standard. Common situations include:

  • Laboratory experiments – compare your experimental result (e.g., density of a metal) to the textbook value.
  • Manufacturing and quality control – check if a product dimension is within tolerance of the design specification.
  • Surveys and predictions – compare a forecast (e.g., election poll, sales estimate) to the actual outcome.
  • Instrument calibration – determine how accurate a sensor or meter is by comparing its reading to a reference standard.

It is especially useful because it normalizes the error – a 2 cm error on a 100 cm object is 2%, but the same 2 cm error on a 10 cm object is 20%. Percentage error lets you compare errors across different scales.

How to Read the Result

The percentage error gives you a dimensionless measure of accuracy. A result of 0% means your measured value exactly matches the accepted value. A result of 5% means your measurement is off by 5% of the true value – not 5 units, but 5% of the accepted value.

For example, if you measured a length as 48 cm and the true length is 50 cm, the error is 2 cm, which is 4% of 50 cm. If the true length were 100 cm and you measured 98 cm, the error is still 2 cm, but the percentage error is only 2%.

Note that percentage error is always positive because you take the absolute value. If you need to know whether your measurement is too high or too low, you can calculate the signed error (without absolute value) separately – but the standard percentage error is always non-negative.

Common Mistakes and Misconceptions

Several pitfalls can lead to incorrect percentage error calculations:

  • Using the measured value as the denominator – The formula divides by the accepted value, not the measured value. Dividing by the measured value gives a different (and usually larger) number.
  • Forgetting absolute value – If you skip the absolute value, you might get a negative percentage, which is not standard for percentage error (though it can be used for signed error).
  • Unit mismatch – Both values must be in the same units. If you measure in inches but the accepted value is in centimeters, convert first.
  • Confusing percentage error with percentage difference – Percentage difference compares two values without a designated “true” one (it divides by the average). Percentage error always has an accepted reference value.
  • Rounding too early – Do all calculations with full precision, then round at the end. Rounding intermediate steps can introduce significant error.

Limitations of the Formula

The percentage error formula assumes the accepted value is not zero. If the accepted value is zero, the formula divides by zero, which is undefined. In such cases, you cannot use percentage error – you would need to use absolute error instead.

Also, the formula gives a relative measure, but it does not tell you anything about the distribution of errors. For multiple measurements, you would typically calculate the mean and standard deviation, and then compare the mean to the accepted value. Percentage error is a single-point comparison.

Finally, the formula treats positive and negative errors symmetrically (due to absolute value). If you need to know the direction of the error, you must look at the signed difference separately.

Alternatives to Percentage Error

Depending on your context, you might use other error measures:

  • Absolute error – Simply |measured − accepted|. Useful when the scale is fixed and you need the error in the same units.
  • Relative error – |measured − accepted| ÷ accepted (without multiplying by 100). This is the decimal form of percentage error.
  • Percentage difference – |a − b| ÷ ((a+b)/2) × 100. Used when neither value is considered the “true” one.
  • Mean absolute percentage error (MAPE) – Average of percentage errors across multiple predictions, often used in forecasting.
  • Root mean square error (RMSE) – Square root of the average squared differences, used when you want to penalize large errors more heavily.

Choose the measure that best fits your goal: percentage error for a single comparison against a known standard, MAPE for multiple forecasts, and RMSE when large errors are especially undesirable.

Frequently Asked Questions

What is the difference between percentage error and percentage difference?

Percentage error uses the accepted value as the denominator and is used when you have a true or reference value. Percentage difference uses the average of the two values as the denominator and is used when you are comparing two values without a designated “true” one. For example, comparing two measurements of the same object would use percentage difference, while comparing a measurement to a published standard would use percentage error.

Can percentage error be negative?

In the standard definition, no – because you take the absolute value of the difference. However, some fields use a “signed error” that keeps the sign to indicate whether the measurement is above or below the accepted value. If you see a negative percentage error, it likely means the author used the signed version, not the absolute value version.

What if the accepted value is zero?

You cannot calculate percentage error when the accepted value is zero because it would involve division by zero. In that case, use absolute error (|measured − 0| = |measured|) or relative error with a different reference. This is a fundamental limitation of any relative measure.

How do I calculate percentage error in Excel?

In Excel, you can use the formula: =ABS((measured - accepted)/accepted)*100. Replace measured and accepted with cell references. For example, if your measured value is in A1 and accepted value in B1, use =ABS((A1-B1)/B1)*100. Format the cell as a number with the desired decimal places.

Is percentage error the same as percent accuracy?

No. Percentage error measures how far your measurement is from the true value. Percent accuracy is often defined as 100% − percentage error, which represents how close your measurement is to the true value as a percentage. For example, a 4% error corresponds to 96% accuracy.

Why do we multiply by 100?

Multiplying by 100 converts the relative error (a decimal) into a percentage. This makes the number easier to interpret and compare across different contexts. For instance, a relative error of 0.04 is less intuitive than 4%.

Related

Formula used
in a | Accepted value | - | 50 | 0
in m | Measured value | - | 48 | 0
out pe | Percentage error | % | (abs(m - a) / a) * 100 | 2
out ad | Absolute difference | - | abs(m - a) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.