ThisCalculator

Everyday

Kenmore Washer F28 Code: How to Unlock & Fix

Updated · Standard formula, shown below

If your Kenmore HE2 washer displays an F28 error code, the machine has detected a communication problem between the main control board and the motor control board. This often locks the washer and prevents it from running. This guide walks you through the steps to unlock the washer and resolve the F28 code, from a simple reset to checking wiring connections.

What You’ll Need

  • Phillips-head screwdriver (for removing the control panel or rear panel if needed)
  • Multimeter (optional, for testing continuity of wires)
  • Flashlight (to see behind the panels)

Step-by-Step

  1. Unplug the washer. Pull the power cord from the wall outlet. Wait at least 5 minutes. This allows the control boards to fully discharge and reset.
  2. Plug the washer back in. After the wait, reconnect the power. Open and close the door firmly. Press the Pause/Cancel button twice to clear any error. If the F28 code is gone and the washer starts, the issue was a temporary glitch.
  3. Check the door latch. If the code returns, inspect the door strike and latch. A loose or broken latch can cause communication errors. Close the door and listen for a distinct click. If the latch is loose, tighten the screws holding the latch to the washer body.
  4. Inspect the wire harness connections. Unplug the washer again. Remove the top panel by prying off the two clips at the front edge, then sliding the panel back and lifting it off. Look for the main control board (usually on the right side). Check the connectors—especially the large white connector—for any loose or corroded pins. Reseat each connector firmly.
  5. Check the motor control board. The motor control board is typically located at the bottom rear of the washer. You may need to lay the washer on its side or remove the rear panel to access it. Inspect the connections on this board as well. Look for burnt marks or a melted connector. If any connector is damaged, replace the harness or the board.
  6. Test the wiring continuity (optional). If you have a multimeter, use it to check the continuity of the wires between the main control board and the motor control board. A break in any wire can trigger F28.
  7. Reassemble and test. After reseating all connectors, reassemble the washer, plug it in, and run a quick wash cycle. If the F28 code does not reappear, the fix was successful.

Common Mistakes

  • Not waiting long enough: A 30-second unplug may not fully discharge the capacitors. Always wait at least 5 minutes.
  • Ignoring the door latch: Many F28 errors are actually caused by a faulty door lock mechanism, not the boards themselves.
  • Replacing parts without checking connections: A loose connector is the most common cause. Always reseat connectors before buying new parts.
  • Forgetting to unplug before touching boards: Always disconnect power before inspecting or handling any electrical component.

Tips

  • Take a photo of the wiring before disconnecting anything. This helps you remember where each connector goes.
  • Use a can of compressed air to blow dust off the control boards. Dust can cause shorts and communication errors.
  • If the washer is still under warranty, contact a professional technician before attempting repairs yourself.
  • Keep the washer level. Excessive vibration can loosen connectors over time.

Troubleshooting

If the F28 code persists after following the steps above, here’s what to try next:

  • Recheck the door latch: Test the door latch with a multimeter for continuity when closed. If it doesn’t read correctly, replace it.
  • Inspect the main control board for burnt components: Look for any swollen capacitors or scorch marks. If found, the board needs replacement.
  • Check the motor harness: The harness between the motor and the motor control board can chafe against the cabinet. Inspect for bare wires and replace if damaged.
  • Try a hard reset: Unplug the washer, wait 10 minutes, then press and hold the Start/Pause button for 5 seconds while plugging it back in. This is a deeper reset for some models.
  • If all else fails: The motor control board itself may be faulty. This is less common but possible. Consider replacing it, or call a qualified appliance technician.

Frequently Asked Questions

What does the F28 error code mean on a Kenmore washer?

F28 indicates a communication failure between the main control board and the motor control board. The washer stops and locks to prevent damage.

Can I reset the F28 code without unplugging the washer?

You can try pressing the Pause/Cancel button twice, but a full power cycle (unplug for 5 minutes) is more reliable.

Is it safe to use the washer if F28 appears?

No. The washer may stop mid-cycle with water in the drum. Unplug it and resolve the error before using it again.

How much does it cost to fix an F28 error?

If it’s just a loose connection, it’s free. If you need to replace a control board, the part can cost anywhere from $100 to $250, plus labor if you hire a technician.

Can a power surge cause the F28 code?

Yes, a power surge can corrupt the communication between boards. A reset often clears it, but repeated surges may damage the boards.

How do I know if I need to replace the motor control board?

If you’ve checked all wiring and connectors, and the board shows no visible damage, but the error persists, the board is likely faulty. A multimeter test of the board’s output voltage can confirm, but this is advanced.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.