ThisCalculator

Everyday

Set Building Decay on a Conan Exiles Server

Updated · Standard formula, shown below

This guide explains how to set building decay on a Conan Exiles server, whether you run a dedicated server or use a hosting panel. Building decay automatically removes structures that haven’t been touched by their owner for a set number of days, freeing up server resources and preventing abandoned bases from cluttering the map. You’ll need access to the server’s configuration files or its control panel.

What You’ll Need

  • Administrator access to your Conan Exiles server (either the server files or a hosting provider’s control panel).
  • For dedicated servers: the ability to edit the ServerSettings.ini or Game.ini file, depending on your setup.
  • For console servers (Xbox/PlayStation): a server hosting service that provides config file editing, as decay settings are not exposed in the in-game server menu.

Step-by-Step

  1. Stop your server. Always stop the server before editing configuration files to avoid changes being overwritten or corrupted.
  2. Locate the configuration file. For a dedicated server, navigate to the server’s ConanSandbox/Saved/Config/WindowsServer (Windows) or LinuxServer folder. In hosting panels, look for a “Config Files” or “Server Settings” section.
  3. Open the correct file. Decay settings are typically in ServerSettings.ini. Some older guides mention Game.ini, but the official setting is in ServerSettings.ini under the [ServerSettings] section.
  4. Find or add the decay setting. Look for a line that starts with BuildingDecayEnabled. If it’s not there, add it under [ServerSettings].
  5. Set the value. To enable decay, set it to True. To disable decay, set it to False. Example: BuildingDecayEnabled=True.
  6. Adjust the decay time. The setting BuildingDecayTimeMultiplier controls how fast decay happens. The default is 1.0. Lower values (e.g., 0.5) make decay happen faster; higher values (e.g., 2.0) slow it down. This multiplier applies to the base decay timers (which are about 7 days for most building pieces, but vary by material and structure type).
  7. Optionally adjust decay for specific structure types. You can set BuildingDecayOwnedTimeMultiplier and BuildingDecayDisrepairTimeMultiplier to fine-tune how long a structure stays after the owner stops interacting, and how long it takes to fall into disrepair. Leave these at 1.0 if you’re not sure.
  8. Save the file. Make sure the file is saved in UTF-8 format (most editors do this by default).
  9. Restart your server. Start the server again. The new decay settings will take effect immediately.
  10. Verify the settings. In-game, check the decay timer on any building piece you own (look at a foundation and press the “show decay” key, usually Tab on PC). The timer should reflect your new multiplier.

Common Mistakes

  • Editing the wrong file. Some hosting panels have multiple config files. Make sure you edit ServerSettings.ini and not Game.ini (unless your host specifically tells you otherwise).
  • Forgetting to stop the server. If you edit while the server is running, the changes may be overwritten when the server shuts down.
  • Using the wrong syntax. The setting must be exactly BuildingDecayEnabled=True (case-sensitive). A missing space or typo will cause the game to ignore it.
  • Setting the multiplier too low. A value like 0.1 will make buildings decay in under a day, which can frustrate players who don’t log in daily.
  • Confusing the multiplier with a time in days. The multiplier is not a number of days; it’s a factor applied to the base decay timers.

Tips

  • If you want to disable decay entirely, set BuildingDecayEnabled=False. This is common for private PvE servers with a small player base.
  • For PvP servers, a decay time of 7–14 days (multiplier 1.0–2.0) is a good balance. For PvE, you might go longer (e.g., 2.0–3.0) to let players keep their builds.
  • Test the settings on a test server first if possible, so you can see how the timers behave before applying to your live server.
  • Communicate the decay settings to your players. Put them in your server description or Discord so players know how often they need to log in to keep their bases.
  • Remember that decay only triggers when a building is not touched (no building pieces placed, repaired, or containers used) for the entire decay period. Simply logging in doesn’t reset the timer; you must interact with your base.

Troubleshooting

  • Decay doesn’t seem to work. Check that BuildingDecayEnabled=True is present and correctly spelled. Also, ensure the server was restarted after the change.
  • Buildings disappear too fast. Increase BuildingDecayTimeMultiplier to a higher value (e.g., 2.0 or 3.0).
  • Buildings never decay. If you set the multiplier very high (like 100), decay will take effectively forever. Check your multiplier and lower it if needed.
  • Changes are not saved after restart. Some hosting panels have a “Save” button that you must click after editing. Also, ensure the server is fully stopped before editing.
  • Players report they can’t see decay timers. Make sure the server has the “Show Building Decay” option enabled in the server settings (this is separate from the decay enable setting). In the in-game server settings menu, look for “Show Building Decay” and set it to “On”.
  • Conflicting settings. If you have multiple config files (e.g., a Game.ini that also has decay settings), they might conflict. Remove any duplicate decay settings from other files.

Frequently Asked Questions

What does the BuildingDecayTimeMultiplier actually do?

It multiplies the base decay timers for all building pieces. A value of 1.0 uses the default timers (roughly 7 days for most pieces, but longer for T3 buildings). A value of 2.0 doubles that time, so buildings last about 14 days before decaying.

Does decay affect all building pieces equally?

No. Higher-tier materials (like black ice or reinforced stone) have longer base decay timers than lower-tier materials (like sandstone). The multiplier applies to all of them proportionally.

Can I set decay per player or per clan?

No, decay settings are global. You can only adjust the overall multiplier, not individual player settings. However, you can use admin commands to manually refresh decay timers for specific players if needed.

Does logging in reset the decay timer?

No. You must actually interact with your base—place a building piece, repair something, or open a container—to reset the decay timer. Simply being online does not reset it.

How do I check the decay timer on my own building?

Look at any building piece you own and press the “show decay” key (default is Tab on PC). A small timer will appear showing how much time is left before that piece decays.

Is there a way to disable decay for a specific building?

No, decay is global. You can’t exempt a specific building from decay. The only workaround is to have the owner touch the building regularly, or use an admin to refresh the timer periodically.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.