ThisCalculator

Everyday

Pair Skullcandy Noise Cancelling Headphones by Model

Updated · Standard formula, shown below

This guide walks you through pairing any Skullcandy noise cancelling headphone model with your phone, tablet, or computer. You’ll learn the exact button presses and menu steps for each current family, plus what to do when pairing fails. Before starting, make sure your headphones are charged and your device’s Bluetooth is turned on.

What You’ll Need

  • Your Skullcandy headphones (charged)
  • The device you want to pair (phone, tablet, computer)
  • Your device’s Bluetooth settings menu

Step-by-Step

The pairing method depends on your model. Below are the steps for each current Skullcandy noise cancelling headphone family.

Crusher ANC / Crusher ANC 2

  1. Power off the headphones. If they are on, press and hold the power button for about 5 seconds until you hear the power-off tone.
  2. Press and hold the power button for about 5 seconds again. You will hear a pairing tone and the LED will blink red and blue.
  3. On your device, open Bluetooth settings and select “Skullcandy Crusher ANC” (or “Crusher ANC 2”) from the list.
  4. Once connected, you’ll hear a confirmation tone. The LED will stop blinking and glow solid blue.

Hesh ANC

  1. With the headphones powered off, press and hold the power button for about 5 seconds.
  2. Release when the LED starts flashing red and blue. You’ll hear a pairing prompt.
  3. Open Bluetooth on your device and select “Skullcandy Hesh ANC”.
  4. Wait for the connection tone. The LED will turn solid blue.

Rail ANC

  1. Ensure the earbuds are in the charging case. Open the case lid.
  2. Take both earbuds out. They will automatically enter pairing mode the first time you use them.
  3. If they don’t enter pairing mode automatically, place them back in the case, close the lid, then reopen and remove them again.
  4. On your device, look for “Skullcandy Rail ANC” in Bluetooth settings and tap to connect.

Grind ANC (true wireless earbuds)

  1. Take both earbuds out of the charging case. They will power on and enter pairing mode automatically (LED blinks red/blue).
  2. If they are already paired to another device, press and hold the touch sensor on both earbuds for 3 seconds to enter pairing mode.
  3. Select “Skullcandy Grind ANC” from your device’s Bluetooth list.
  4. After a few seconds, you’ll hear a chime confirming the connection.

Push ANC (true wireless earbuds)

  1. Remove both earbuds from the case. They will automatically enter pairing mode.
  2. If not, press and hold the touch control on both earbuds for 5 seconds until the LED flashes red/blue.
  3. Choose “Skullcandy Push ANC” in your device’s Bluetooth menu.
  4. Wait for the connection tone.

Smokin’ Buds ANC (if you have this older model)

  1. Turn on the earbuds (they power on when taken out of the case).
  2. Press and hold the multi-function button on the right earbud for about 5 seconds until the LED flashes.
  3. Select “Skullcandy Smokin’ Buds ANC” from your device’s Bluetooth list.

Common Mistakes

  • Not entering pairing mode: Simply powering on the headphones does not put them in pairing mode. You must hold the power button longer (usually 5 seconds) until the LED blinks red/blue.
  • Pairing to an old device: If the headphones were previously paired to another phone, they may auto-connect to that device instead of your new one. Turn off Bluetooth on the old device or forget the headphones on it.
  • Earbuds not in pairing mode: For true wireless earbuds, taking them out of the case usually triggers pairing, but if they’ve been used before, you may need to manually enter pairing mode by holding the touch sensor.
  • Ignoring the charging case: For earbuds, the case is essential for power and reset. If the earbuds don’t respond, place them back in the case, close it, and try again.

Tips

  • Keep the headphones close to your device (within 3 feet) during pairing to avoid interference.
  • If you’re pairing to a computer, make sure Bluetooth is enabled and the device is discoverable. On Windows, go to Settings > Bluetooth & devices > Add device.
  • For multipoint models (like Crusher ANC 2), you can pair two devices simultaneously. After pairing the first, repeat the pairing process with the second device.
  • If you’re having trouble, reset the headphones. For over-ear models, hold the power button for 10 seconds until the LED flashes red. For earbuds, place them in the case, then press and hold the touch sensors for 10 seconds.

Troubleshooting

Headphones don’t appear in Bluetooth list: Make sure they are in pairing mode (LED blinking red/blue). If not, repeat the pairing button hold. Also, check that your device’s Bluetooth is on and scanning.

Pairing fails after several attempts: Forget the headphones on your device (if they appear), then re-enter pairing mode and try again. If that fails, reset the headphones as described in Tips.

Headphones connect but sound is only from one side: This usually indicates a connection issue. Turn off Bluetooth, then turn it back on, and reconnect. If the problem persists, reset the headphones.

Earbuds connect but no sound: Check that the earbuds are properly seated in your ears and that the volume is up on both the device and the earbuds. Some models have touch controls that may have paused the audio.

Can’t pair to a second device: Some models only support one active connection at a time. Disconnect from the first device (turn off its Bluetooth) before pairing to the second.

Frequently Asked Questions

Q: How do I know if my Skullcandy headphones are in pairing mode?
The LED indicator will blink red and blue alternately. You’ll also hear a pairing tone.

Q: Can I pair my Skullcandy headphones to multiple devices?
Only some models support multipoint (like Crusher ANC 2). Most models connect to one device at a time. For multipoint, pair both devices and then switch between them by pausing audio on one and playing on the other.

Q: Why won’t my Skullcandy earbuds enter pairing mode?
Make sure they are charged and have been reset. Place them in the case, close it, wait 5 seconds, then take them out. If they still don’t enter pairing mode, press and hold the touch sensors for 10 seconds to reset.

Q: How do I reset my Skullcandy headphones?
For over-ear models, press and hold the power button for 10 seconds until the LED flashes red. For earbuds, place them in the case and hold the touch sensors for 10 seconds. This clears the pairing list.

Q: My Skullcandy headphones are paired but keep disconnecting.
Ensure they are fully charged. Move closer to the device and away from other Bluetooth devices or Wi-Fi routers. If the problem continues, reset the headphones and re-pair.

Q: Can I use the Skullcandy app to pair?
The Skullcandy app (available for most models) can help with firmware updates and customizing controls, but pairing is done through your device’s Bluetooth settings. The app may guide you through the process.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.