ThisCalculator

Everyday

Change Tick Rate on Conan Exiles Server

Updated · Standard formula, shown below

Change Tick Rate on Conan Exiles Server

Changing the tick rate on a Conan Exiles server adjusts how often the server updates the game world, affecting performance and responsiveness. This guide covers both dedicated servers and single-player settings, explaining what you need and the exact steps to modify the tick rate.

What You’ll Need

  • Access to your server’s configuration files (for dedicated servers) or the ability to edit game files (for single-player).
  • A text editor like Notepad++ or Visual Studio Code for editing .ini files.
  • Basic understanding of server administration (for dedicated servers).

Step-by-Step

For Dedicated Servers

  1. Stop the server – Before editing any files, shut down your Conan Exiles server to avoid file conflicts or corruption.
  2. Locate the configuration file – The main settings file is usually named ServerSettings.ini and is found in the ConanSandbox/Saved/Config/WindowsServer (or LinuxServer) folder within your server directory. If you use a hosting panel, look for a “Config Files” or “Server Settings” section.
  3. Open the file – Use a text editor to open ServerSettings.ini.
  4. Find the tick rate setting – Look for a line that starts with ServerTickRate=. If it doesn’t exist, you can add it under the [/Script/ConanSandbox.ConanSandboxGameSession] section (or the appropriate section for your server).
  5. Change the value – Set the number to your desired tick rate. Common values are 30 (default), 60, or 120. Higher values mean more updates per second, which can improve responsiveness but increase CPU load.
  6. Save the file – Save your changes and close the editor.
  7. Restart the server – Start your server again. The new tick rate will take effect.

For Single-Player / Co-Op (Non-Dedicated)

  1. Exit the game – Make sure Conan Exiles is completely closed.
  2. Navigate to the config folder – Go to %LOCALAPPDATA%\ConanSandbox\Saved\Config\WindowsNoEditor (on Windows). You can paste this into the address bar of File Explorer.
  3. Open Game.ini – Look for a file named Game.ini. If it doesn’t exist, create a new text file and rename it to Game.ini.
  4. Add the tick rate setting – Add the following lines to the file: 
    [\/Script\/ConanSandbox.ConanSandboxGameSession]
ServerTickRate=60

    Replace 60 with your desired tick rate.

  5. Save and close – Save the file and launch the game. The setting will apply to your single-player session.

Common Mistakes

  • Editing the wrong file – For dedicated servers, ensure you edit ServerSettings.ini, not Game.ini. For single-player, use Game.ini in the correct folder.
  • Incorrect section header – The setting must be under the correct section ([/Script/ConanSandbox.ConanSandboxGameSession]). Placing it elsewhere will cause it to be ignored.
  • Using a comma instead of a period – Some locales use commas for decimals, but tick rate is an integer, so just use whole numbers.
  • Not restarting the server – Changes only take effect after a full restart.
  • Setting too high a value – Values above 120 may cause instability or performance issues, especially on lower-end hardware.

Tips

  • Start with 60 – For most servers, 60 is a good balance between performance and responsiveness. Only go higher if you have a powerful CPU and need minimal input lag.
  • Monitor server performance – After changing the tick rate, keep an eye on CPU usage and server FPS (if applicable). If the server struggles, lower the value.
  • Backup your config – Before making changes, copy the original file to a safe location so you can revert if needed.
  • Use a tool for remote editing – If you’re using a hosting provider, many offer a web-based file manager that lets you edit config files easily.

Troubleshooting

  • Setting doesn’t take effect – Double-check that you placed the line under the correct section and that the file is saved in the right location. Also, ensure the server is fully stopped before editing.
  • Server won’t start – If the server fails to start after the change, revert to the backup and try again. Make sure the tick rate value is a positive integer (e.g., 30, 60, 120).
  • Game crashes on launch (single-player) – Verify that Game.ini is in the correct folder and has the correct syntax. A missing section header is a common cause.
  • No visible difference – The tick rate may not be noticeable in all scenarios. Test with fast actions like combat or building to see the difference.
  • Performance drops – If you experience lag, reduce the tick rate back to 30 or 60. The server’s CPU may not handle high rates.

Frequently Asked Questions

What is the default tick rate in Conan Exiles?

The default is 30 ticks per second. This is a common value for many game servers, balancing performance and responsiveness.

Does changing the tick rate affect gameplay?

Yes, a higher tick rate can make actions like combat and building feel smoother and more responsive. However, it can also increase server CPU load and may cause rubber-banding if the server can’t keep up.

Can I set the tick rate to 1000?

Technically you can, but it’s not recommended. Values above 120 are rarely beneficial and can cause server instability. Stick to 30, 60, or 120 for best results.

Will changing the tick rate fix lag?

Not necessarily. Lag can be caused by network issues, server hardware, or mods. While a higher tick rate can reduce input delay, it won’t fix all lag sources.

Is the tick rate the same as the server FPS?

No. Tick rate is how often the server updates the game simulation, while FPS (frames per second) is how often the graphics are rendered. They are independent.

Do I need to change the tick rate on both the server and client?

No, the server’s tick rate is authoritative. Clients automatically adapt to the server’s tick rate.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.