ThisCalculator

Everyday

Acid Percent to Molarity Conversion

Updated · Standard formula, shown below

The calculator for this page is switched off while it is checked. The formula is below, and the worked example in the article shows how to use it by hand.

This calculator converts an acid’s percent concentration (weight/weight, % w/w) to molarity (mol/L). You enter the percent value, the acid’s density (g/mL), and its molar mass (g/mol), and it returns the molarity. The formula is straightforward: molarity = (percent × density × 10) ÷ molar mass.

Formula

The conversion uses the definition of molarity and the meaning of percent concentration:

Molarity (mol/L) = (Percent (% w/w) × Density (g/mL) × 10) ÷ Molar mass (g/mol)

Where:

  • Percent (% w/w) – grams of solute per 100 grams of solution (e.g., 37% means 37 g HCl in 100 g solution).
  • Density (g/mL) – mass of 1 mL of solution. For concentrated acids, density is usually >1 g/mL.
  • Molar mass (g/mol) – mass of one mole of the acid (e.g., HCl = 36.46 g/mol, H₂SO₄ = 98.08 g/mol).
  • 10 – converts g/mL to g/L (since 1 mL = 0.001 L, multiplying by 1000/100 = 10).

Worked Example

Using the default values (37% HCl, density 1.19 g/mL, molar mass 36.46 g/mol):

  1. Start with percent: 37% = 37 g HCl per 100 g solution.
  2. Find mass of HCl in 1 L of solution: density 1.19 g/mL → 1 L = 1000 mL → mass = 1000 × 1.19 = 1190 g solution.
  3. Mass of HCl in that 1 L = 1190 × (37/100) = 440.3 g.
  4. Moles of HCl = 440.3 ÷ 36.46 = 12.08 mol.
  5. Since that is in 1 L, molarity = 12.08 mol/L (rounded to 12.08).

The calculator gives the same result: (37 × 1.19 × 10) ÷ 36.46 = 12.08 M.

Why Percent to Molarity Matters

Acids are often sold as concentrated solutions with percent labels (e.g., “37% HCl”, “98% H₂SO₄”). But many lab protocols require molarity. Molarity tells you the number of moles per liter, which is what you use in stoichiometry, dilutions, and reaction calculations. Converting percent to molarity lets you prepare accurate dilutions from stock bottles.

For example, to make 1 L of 1 M HCl from 12 M stock, you would take 83.3 mL of stock and dilute to 1 L. Without knowing the stock’s molarity, you cannot do this correctly.

How to Choose the Right Density and Molar Mass

You must use the density of the specific acid solution you have, not just the pure acid. Density depends on concentration and temperature. Most commercial acid bottles list the density on the label. If not, you can look up a density table for that acid at that percent.

Molar mass is fixed for each acid:

  • HCl – 36.46 g/mol
  • H₂SO₄ – 98.08 g/mol
  • HNO₃ – 63.01 g/mol
  • CH₃COOH (acetic) – 60.05 g/mol

For a mixture or unknown acid, you cannot use this formula without knowing the molar mass.

Common Mistakes and How to Avoid Them

  • Using percent by volume (v/v) instead of weight/weight. This formula only works for % w/w. If your label says % v/v, convert to w/w first using density.
  • Forgetting the factor of 10. The 10 comes from converting 100 g to 1 L and g/mL to g/L. Omitting it gives a result 10 times too small.
  • Using density of pure acid instead of the solution. For 37% HCl, pure HCl gas density is irrelevant; you need the solution density (≈1.19 g/mL).
  • Rounding too early. Keep extra digits until the end to avoid rounding errors, especially when doing dilutions.

Limitations and When to Use Alternatives

This formula assumes the percent is weight/weight and that the solution is at the density you entered. If the acid is a hydrate (like some solid acids), molar mass changes. For very dilute solutions, density approaches 1 g/mL, but for concentrated acids it is significantly different.

If you have percent by weight/volume (w/v), the conversion is simpler: molarity = (percent w/v × 10) ÷ molar mass. But that is a different formula.

Safety and Handling

Concentrated acids are corrosive and can cause severe burns. Always wear appropriate personal protective equipment (gloves, goggles, lab coat) and work in a fume hood when handling volatile acids like HCl and HNO₃. When diluting, always add acid to water slowly, never water to acid, to prevent violent splattering. Store acids in clearly labeled, compatible containers away from bases and oxidizers.

Frequently Asked Questions

What does % w/w mean?

% w/w means grams of solute per 100 grams of solution. For example, 37% HCl means 37 g of HCl gas dissolved in 63 g of water, totaling 100 g of solution.

Can I use this for any acid?

Yes, as long as you know the percent (w/w), density, and molar mass. It works for any solute, acid or not, as long as it is dissolved in a solvent.

What if my acid label shows % v/v?

You must convert % v/v to % w/w first. Use the density of the solute and the solution. For example, if you have 10% v/v ethanol in water, you need the density of ethanol and the solution to find grams of ethanol per 100 g solution.

How do I convert molarity back to percent?

Rearrange the formula: percent = (molarity × molar mass) ÷ (density × 10). For example, 12 M HCl with density 1.19 g/mL gives (12 × 36.46) ÷ (1.19 × 10) = 36.8%.

Why is concentrated HCl about 12 M, not 37 M?

Because 37% HCl has a density of about 1.19 g/mL. The molarity works out to about 12 M. The percent is by weight, not by volume, so you cannot just take 37% of 1000 mL.

Does temperature affect the conversion?

Yes, density changes with temperature. For precise work, use the density at the temperature of your solution. Most lab density values are given at 20°C.

Related

Formula used
in p | Percent (w/w) | % | 37 | 0
in d | Density | g/mL | 1.19 | 0
in m | Molar mass | g/mol | 36.46 | 0
out M | Molarity | mol/L | (p * d * 10) / m | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.