Varas to Feet Texas: Conversion & History
- Inches
- in
- Result
- Meters
- m
- Result
- Varas
- 10 varas
- You entered
This page converts the Spanish vara to feet, specifically for the Texas vara (33⅓ inches), and explains how to do the math yourself. Enter a number of varas and you get the equivalent length in feet, along with the calculation shown step by step. The Texas vara equals 2.777… feet, so 1 vara is 2 feet 9⅓ inches.
Formula
The Texas vara is defined as 33⅓ inches (exactly 100/3 inches). To convert varas to feet, divide the number of inches by 12:
Feet = Varas × (33⅓ ÷ 12)
Since 33⅓ ÷ 12 = 2.777…, the formula is:
Feet = Varas × 2.7777777778
Where:
- Varas = the number of Spanish varas (dimensionless count)
- Feet = the equivalent length in U.S. survey feet
For metric users, 1 Texas vara = 0.8466666667 meters exactly (because 33⅓ inches × 0.0254 m/in = 0.846666… m).
Worked Example
Using the default value of 10 varas:
- Start with 10 varas.
- Multiply by 2.7777777778 ft/vara: 10 × 2.7777777778 = 27.777777778 ft.
- Round to two decimals: 27.78 feet.
So 10 Texas varas = 27.78 feet (or 27 feet 9⅓ inches). The calculator shows the same result.
What Is a Vara?
The vara is an old Spanish unit of length, originally based on the distance from the shoulder to the fingertips—roughly a “yard” in the Spanish-speaking world. Its exact length varied by country and even by city. In Spain, the vara was about 2.74 feet (0.8359 m), but in the Americas, each colony often set its own standard.
Texas, as part of New Spain and later Mexico, used the vara for land measurement. When Texas became a republic and then a U.S. state, the old Spanish land grants remained valid. To avoid disputes, the state legally defined the Texas vara as 33⅓ inches in 1919 (and reaffirmed it later). This is slightly longer than the Spanish vara but shorter than the Mexican vara used in some other states.
Why Texas Still Uses Varas
You might wonder why a modern U.S. state still deals with a colonial-era unit. The answer is land records. Thousands of original land grants, surveys, and deeds in Texas were written in varas. When property lines are re-surveyed, contested, or subdivided, surveyors must convert those old measurements to feet and meters.
For example, a typical Spanish land grant might be described as “5,000 varas square.” That’s about 4,166.7 feet per side, or roughly 0.79 miles. Without a consistent conversion, boundary disputes would be endless. The Texas General Land Office and county surveyors routinely use the 33⅓-inch vara.
How to Convert Varas to Feet Yourself
You can do the conversion with a calculator or by hand:
- Multiply the number of varas by 2.7777777778 to get feet.
- For inches, multiply varas by 33.333333333.
- For meters, multiply varas by 0.8466666667.
- To go the other way, divide feet by 2.7777777778 (or multiply by 0.36) to get varas.
Example: 100 varas × 2.7777777778 = 277.78 feet. That’s about 84.7 meters.
Common Mistakes and Misconceptions
The biggest error is using the wrong vara definition. There isn’t one universal vara. The Spanish vara (2.74 ft), the Mexican vara (2.78 ft), and the Texas vara (2.777… ft) are all different. If you’re working with Texas land records, always use the Texas value. If you’re reading an old Spanish document from California or New Mexico, that region may have used a different vara.
Another mistake is rounding too early. The Texas vara is exactly 33⅓ inches, so 2.777… feet is a repeating decimal. If you round to 2.78 feet, you introduce a small error that can grow over long distances. For precise survey work, keep full precision until the final answer.
Also, note that the U.S. survey foot vs. international foot distinction matters in large surveys. The Texas vara is defined in terms of the U.S. survey foot (which is exactly 1200/3937 meters). Our calculator uses the international foot (0.3048 m) for simplicity; the difference is about 2 parts per million, negligible for most uses.
Practical Uses Today
Beyond historical land grants, varas still appear in:
- Property deeds and easements in Texas, especially in rural areas.
- Oil and gas leases, where old surveys are referenced.
- Road right-of-way descriptions in some counties.
- Archaeological and historical research on Spanish colonial settlements.
If you’re buying land in Texas and the deed mentions varas, you now know how to convert to feet. For example, a 200-vara frontage is 555.56 feet (about 0.105 miles). A 1,000-vara deep lot is 2,777.78 feet (about 0.526 miles).
Limitations of the Formula
The conversion formula is exact only for the Texas vara. If you’re dealing with a different regional vara, you must adjust the factor. Also, the formula assumes a straight-line measurement, not accounting for terrain or curvature. For legal purposes, always consult a licensed surveyor; don’t rely on a simple conversion for boundary disputes.
Finally, remember that the vara is a linear measure, not an area. If you see “square varas,” you’ll need to convert each dimension separately or use a conversion factor of 7.716 square feet per square vara (since 2.777…² ≈ 7.716).
Frequently Asked Questions
How many feet are in a Texas vara?
Exactly 2.7777777778 feet, which is 2 feet and 9⅓ inches. This is because a Texas vara is defined as 33⅓ inches.
Is a vara the same as a yard?
No. A yard is exactly 3 feet (36 inches). A Texas vara is 33⅓ inches, so it’s about 2.78 feet—slightly shorter than a yard by 2⅔ inches. The Spanish vara was closer to a yard but still not identical.
Why is the Texas vara different from the Spanish vara?
When Spain colonized the Americas, each region often adopted its own standard. The Texas vara was set at 33⅓ inches by state law to match the measurements used in early land grants. The Spanish vara is about 32.91 inches, slightly shorter.
Can I convert varas to acres?
You can, but only if you have square varas. One square vara equals about 7.716 square feet. Since an acre is 43,560 square feet, one acre is about 5,645.4 square varas. For a rectangular plot, convert each side to feet first, then multiply and divide by 43,560.
Do modern Texas surveys still use varas?
Yes, especially in areas with original Spanish land grants. Surveyors often convert varas to feet for new plats, but the old records remain in varas. The Texas General Land Office maintains conversion tables for this purpose.
Related
Formula used
in v | Varas | varas | 10 | 0 out ft | Feet | ft | v * 2.7777777778 | 2 out in | Inches | in | v * 33.333333333 | 1 out m | Meters | m | v * 0.8466666667 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.