Ethernet Cable Splitters: What They Are & Best Picks
Ethernet cable splitters let you run two devices over a single network cable, but they only work in pairs and are not the same as switches. The best ones to buy are simple, passive RJ45 splitter kits that support Fast Ethernet (100 Mbps) and come with two female ports on each end. This article explains how they work, where they make sense, and what to look for when buying.
What Is an Ethernet Cable Splitter?
An Ethernet cable splitter is a small, passive device with one RJ45 port on one side and two RJ45 ports on the other. It does not actually split a signal like a power strip splits electricity. Instead, it uses the unused wires in a standard Cat5e or Cat6 cable to carry two separate 100 Mbps data streams over a single cable run.
Standard Ethernet cables have four twisted pairs (8 wires), but 100 Mbps Ethernet only uses two of those pairs (pins 1, 2, 3, and 6). The other two pairs (pins 4, 5, 7, and 8) are unused. A splitter kit takes advantage of this by sending one device’s signal over the first two pairs and the other device’s signal over the remaining two pairs.
How Does an Ethernet Splitter Work?
You must use splitters in pairs. One splitter connects to your router or switch, and the other connects at the far end of the cable where your two devices are located. The two devices plug into the splitter at the far end, and the single cable between the two splitters carries both signals.
Here is a step-by-step breakdown of a typical setup:
- Connect the two output ports of the splitter near your router to two LAN ports on the router (or switch).
- Run a single Ethernet cable from the splitter’s single port to the single port on the second splitter at the other end.
- Plug your two devices (e.g., a computer and a smart TV) into the two ports on the far-end splitter.
Both devices will get a network connection, but the speed is limited to 100 Mbps (Fast Ethernet). Gigabit Ethernet (1000 Mbps) uses all four pairs, so a passive splitter will not work for gigabit speeds. If you need gigabit, you need a network switch instead.
What to Look for When Buying an Ethernet Splitter
Not all splitters are created equal. Here are the key factors to consider:
- Speed rating: Look for splitters explicitly rated for 100 Mbps. Some cheap ones may not even meet that reliably. Avoid any that claim gigabit support—they are either switches or misleading.
- Pairing requirement: Ensure the product is sold as a kit with two identical splitters. Some are sold individually, but you still need two.
- Connector quality: Gold-plated contacts and a sturdy plastic housing usually indicate better build quality. Avoid flimsy connectors that can break.
- Compatibility: Splitters work with Cat5, Cat5e, and Cat6 cables. They are backward compatible with 10 Mbps Ethernet too.
- PoE (Power over Ethernet): Passive splitters do not support PoE. If you need to power a device like an IP camera, use a PoE splitter or a switch.
Common Problems and Misconceptions
The biggest misconception is that an Ethernet splitter can double your cable capacity without any downsides. In reality, you are trading speed for cable count. If you have gigabit internet, a splitter will bottleneck your connection to 100 Mbps on both devices.
Another common issue is using a splitter when a switch would be better. A switch is an active device that needs power but provides full gigabit speeds to multiple devices. Splitters are only useful when you have a single pre-existing cable run and cannot pull another one, and when 100 Mbps is sufficient for your needs.
Also, some people try to use a splitter to connect two cables to one port on a router. That does not work—the router port expects one device. Splitters only work in the paired configuration described above.
Ethernet Splitter vs. Switch: Which Should You Choose?
If you have multiple devices at one location and a single cable, a switch is almost always the better choice. Here is why:
- Speed: A switch supports gigabit speeds (or even 2.5G/10G) and does not reduce bandwidth.
- Flexibility: You can connect more than two devices by using a switch with more ports.
- Power: Switches need a power outlet, but they can also support PoE for cameras or phones.
- Cost: A basic 5-port gigabit switch is often cheaper than a pair of splitters and gives far better performance.
Use a splitter only when you have no power outlet at the far end, you only need two devices, and 100 Mbps is acceptable. Otherwise, buy a switch.
Cost and Where to Buy
Ethernet splitter kits are inexpensive. A pair of basic splitters typically costs between $8 and $15, depending on the brand and build quality. You can find them at electronics stores, online marketplaces, and office supply retailers. Prices vary, but they are generally cheaper than a gigabit switch (which starts around $15–$20).
When comparing prices, check whether the listing includes two units. Some sellers list a single splitter, and you would need to buy two separately. Also, check the cable length you need—splitters do not extend cable runs beyond the standard 100-meter limit for Ethernet. If your run is already near that limit, a splitter will not help.
Safety and Installation Tips
Ethernet splitters are passive and low-voltage, so there is little safety risk. However, follow these guidelines:
- Do not use splitters with PoE devices. The unused pairs carry power in PoE, and a passive splitter can damage equipment.
- Keep splitters away from heat sources and moisture. They are not rated for outdoor use unless specified.
- Ensure the cable is not kinked or bent sharply, as this can degrade signal quality.
- If you are running cable through walls, use a solid-core cable and terminate it properly—do not just rely on splitters to extend a run.
Frequently Asked Questions
Do Ethernet splitters reduce speed?
Yes, they cap speed at 100 Mbps because they only use two of the four twisted pairs. If your internet plan is faster than 100 Mbps, you will be limited to that speed on the connected devices.
Can I use an Ethernet splitter to connect two devices to one router port?
No. A splitter requires two ports on the router side. If you only have one free port, you need a network switch, not a splitter.
Will an Ethernet splitter work with Cat6 cables?
Yes, Cat6 cables work fine with splitters. The splitter does not care about the cable category, but the speed is still limited to 100 Mbps.
Can I use an Ethernet splitter for PoE?
No, standard passive splitters do not support Power over Ethernet. If you need PoE, use a PoE switch or a PoE splitter designed for that purpose.
How do I know if my splitter is working?
Check the link lights on your devices. Both devices should show a solid link light. If not, try swapping the splitter pairs or testing the cable with a simple cable tester.
Is it better to use a splitter or a switch?
For most people, a switch is better because it offers gigabit speeds and more ports. Use a splitter only if you have no power outlet and only need two 100 Mbps connections.
Related
Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.