ThisCalculator

Everyday

3D Printer Upgrades You Can Print Yourself

Updated · Standard formula, shown below

Filament cost 0.10 $
Filament used
10 g
Result
Print time
120 min
You entered
Number of parts
1
You entered

You can print dozens of functional upgrades for your 3D printer, from cable clips and filament guides to full tool organizers and enclosure brackets. These printable parts improve organization, print quality, and convenience without costing anything beyond the filament you already have. This article covers the most useful self-printed upgrades, how to design or find them, and what to consider before installing them.

Formula

The calculator above estimates the filament cost and weight for printing your own upgrades. The formula is:

Cost = (Print time in hours) × (Filament cost per hour) × (Number of parts)

Where:

  • Print time (t) – total time to print one part, in minutes.
  • Number of parts (n) – how many copies you print.
  • Filament cost per hour – assumed at $0.05 per hour (based on a typical 1kg spool costing $20–25 and a printer using ~250g per 10 hours).
  • Filament weight per hour – assumed at 5g per hour (a rough average for a 0.4mm nozzle at 60mm/s).

These are estimates; your actual values depend on your printer speed, layer height, infill, and filament price.

Worked Example

Using the default values: print time = 120 minutes (2 hours), number of parts = 1.

  1. Convert print time to hours: 120 / 60 = 2 hours.
  2. Filament cost = 2 hours × $0.05/hour × 1 = $0.10.
  3. Filament weight = 2 hours × 5g/hour × 1 = 10g.

So a 2-hour print costs about 10 cents in filament and uses 10 grams. That’s typical for a small upgrade like a cable clip or filament guide.

Why Print Your Own Upgrades?

Printing your own upgrades saves money compared to buying commercial parts, and it lets you customize the design to fit your exact printer model. Many popular upgrades are available free on sites like Thingiverse, Printables, and MyMiniFactory. You can also modify existing designs with free software like Tinkercad or Fusion 360 (personal license).

Beyond cost, printed upgrades are lightweight, replaceable, and you can reprint them in different colors or materials. They also reduce the need for metal brackets or plastic parts that may not fit your specific machine.

Top Printable Upgrades

Here are some of the most useful upgrades that are commonly printed:

  • Cable chains and clips – keep wires organized and prevent snags.
  • Filament guides – reduce friction and tangling on spool holders.
  • Spool holder adapters – fit different spool sizes to your stock holder.
  • Tool holders – mount scrapers, pliers, and tweezers to the frame.
  • Drawer and bin organizers – sort nozzles, screws, and small parts.
  • Part cooling fan ducts – improve cooling for better overhangs (design must match your hotend).
  • Z-axis stabilizers – reduce wobble on some models (e.g., Ender 3).
  • Screen covers and knobs – protect the LCD and make adjustments easier.

These are all printable with standard PLA or PETG, and most take under 3 hours each.

How to Choose the Right Upgrade

First, identify a problem: stringing, poor first layer, wire tangles, or missing tools. Then search for a design specifically for your printer model (e.g., “Ender 3 cable chain”). Check the design’s comments and ratings to see if others had success. Consider the material:

  • PLA – cheap, easy to print, but deforms in hot environments (like inside an enclosure).
  • PETG – stronger and heat-resistant up to ~70°C, good for functional parts.
  • ABS/ASA – heat-resistant but needs a heated bed and enclosed printer.

For most upgrades, PETG is a safe choice. If the part is near the hotend or bed, use ABS or a heat-resistant material like PC (polycarbonate) if your printer can handle it.

Common Problems and Fixes

When printing upgrades, you may run into these issues:

  • Poor fit – parts may be too tight or loose due to printer calibration. Adjust print settings (e.g., horizontal expansion) or scale slightly in your slicer.
  • Warping – large flat parts can warp with PLA if the bed isn’t hot enough. Use a brim and ensure bed adhesion.
  • Layer separation – if the part fails along layer lines, increase infill or print with more walls.
  • Heat deformation – if a part near the hotend melts, switch to a higher-temperature filament.

Always test the part on a small section before printing the full upgrade, especially for fan ducts that affect cooling.

Safety Considerations

Printed parts are generally safe, but keep these points in mind:

  • Do not use printed parts for structural support of heavy components (like the print head) unless the design is proven and printed with adequate infill.
  • Keep printed parts away from the heater block and nozzle. PLA melts at ~180°C, so a part touching the hotend will fail.
  • When printing ABS or ASA, ensure proper ventilation and use an enclosure to avoid fumes.
  • Check that printed cable guides don’t pinch wires, which could cause shorts.

Alternatives to Printing

If you don’t want to print, you can buy metal or injection-molded upgrades, but they cost more and may not fit exactly. Another alternative is to redesign your printer layout (e.g., moving the spool holder) without any new parts. For some upgrades like a glass bed or all-metal hotend, printing is not an option—you need purchased parts.

Frequently Asked Questions

Do printed upgrades actually improve print quality?

Some do, like better part-cooling ducts that reduce stringing and improve overhangs. Others, like cable clips, only improve convenience. It depends on the upgrade; research each one for your specific printer.

What filament should I use for printed upgrades?

PETG is a good all-rounder for functional parts. PLA is fine for non-heat areas, but it may deform in a hot car or enclosure. ABS/ASA are better for heat resistance but require more effort to print.

Can I print upgrades without a 3D printer?

No, you need a printer to print them. If you don’t have one, you could use a local makerspace or online printing service, but that adds cost.

Are printed upgrades safe for electrical components?

Yes, as long as they don’t directly contact hot wires or terminals. Use printed cable clips to route wires away from moving parts, but ensure they don’t pinch or abrade insulation.

How do I know if a design is good?

Check the number of downloads, user comments, and whether the designer provides print settings. If possible, print a small test piece first.

Can I sell printed upgrades?

You can, but check the license of the design. Many are Creative Commons Non-Commercial, meaning you can’t sell them. Look for designs with a “Commercial Use” allowed license.

Related

Formula used
in t | Print time | min | 120 | 0
in n | Number of parts | - | 1 | 1
out cost | Filament cost | $ | (t / 60) * 0.05 * n | 2
out weight | Filament used | g | (t / 60) * 5 * n | 0

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.