ThisCalculator

Everyday

Six Cent 3D Print: Is It Really Impressive?

Updated · Standard formula, shown below

Material cost 0.24 USD
Cost per hour
0.32 USD/h
Result
Print time
45 min
You entered
Filament used
12 g
You entered

Yes, a six-cent 3D print can be genuinely impressive, but the real achievement isn’t the cost—it’s what that cost represents: a successful balance of material choice, print settings, and design efficiency. This article explains what a six-cent print typically involves, how to judge its quality, and why the price tag alone isn’t the whole story.

Formula

The material cost of a 3D print is calculated as:

Cost = (Filament used in grams / 1000) × Filament price per kilogram

Where:

  • Filament used (m) – the weight of plastic actually extruded, in grams (g).
  • Filament price per kg (c) – the cost of one kilogram of filament, in your local currency (e.g., USD).
  • Cost – the material cost of the print, in the same currency.

The calculator also shows cost per hour, which divides the material cost by the print time in hours—useful for comparing efficiency across different prints.

Worked Example

Using the default values from the calculator (45 minutes, 12 grams of filament, $20 per kg):

  1. Convert filament used to kilograms: 12 g ÷ 1000 = 0.012 kg
  2. Multiply by price per kg: 0.012 kg × $20/kg = $0.24
  3. So the material cost is $0.24 (24 cents), not six cents.

To get a six-cent print, you would need either less filament (e.g., 3 g at $20/kg) or cheaper filament (e.g., 12 g at $5/kg). The calculator lets you adjust these inputs to match your situation.

Why a Six-Cent Print Can Be Impressive

A six-cent print usually means the object is small, lightweight, and uses minimal material. Common examples include:

  • A simple keychain tag (about 5–8 g)
  • A cable clip (about 2–4 g)
  • A small chess piece (about 8–12 g)
  • A phone stand (about 15–25 g, but still under a dollar)

The impressiveness comes from the fact that you turned a digital model into a physical object for less than the cost of a paperclip. But the real skill is in optimizing the design—using infill wisely, choosing the right layer height, and avoiding unnecessary supports—to achieve that low weight without sacrificing function.

How to Judge a 3D Print’s Quality

Cost alone doesn’t make a print impressive. Look for these quality indicators:

  • Layer adhesion – Does the print break easily along layer lines? Good adhesion means proper temperature and speed.
  • Surface finish – Are there visible blobs, stringing, or gaps? These indicate poor retraction or cooling.
  • Dimensional accuracy – Does the part fit where it should? Measure critical dimensions with calipers.
  • Strength – Does it withstand the intended load? Infill percentage and wall count matter more than cost.

A six-cent print that fails its purpose is not impressive; a six-cent print that works perfectly is.

Common Misconceptions

Misconception: “Six cents means the print is cheap quality.” Not necessarily. The cost is determined by weight, not quality. A well-tuned printer can produce a flawless small part for pennies.

Misconception: “The cost includes electricity and wear.” No, the six-cent figure usually only covers the plastic filament. Electricity, printer maintenance, and your time are extra. A typical 3D printer uses about 50–150 watts, so an hour of printing might cost a few cents in electricity, depending on your local rate.

Misconception: “All filaments cost the same.” Far from it. PLA can be $15–30 per kg, while specialty filaments like carbon-fiber nylon can exceed $100 per kg. The same print could cost six cents or sixty cents depending on material.

How to Achieve a Six-Cent Print

If you want to minimize material cost, consider these factors:

  • Design for low weight – Hollow out parts, reduce infill to 10–20%, and use fewer perimeters.
  • Use a smaller nozzle – A 0.2 mm nozzle uses less plastic but increases print time.
  • Optimize orientation – Avoid supports by orienting the model so overhangs are minimal.
  • Choose cheaper filament – Standard PLA is usually the most affordable option.
  • Print in bulk – Many small parts on one plate can share the same setup time, though material cost per part stays the same.

Remember that reducing weight too much can weaken the part. Test prototypes to find the balance between cost and function.

Alternatives to a Six-Cent Print

If your goal is simply to save money, consider whether 3D printing is the best method:

  • CNC machining – Better for strong, precise parts, but setup costs are higher.
  • Injection molding – Extremely cheap per unit, but only for large production runs.
  • Buying a ready-made part – For standard items like cable clips, a pack of 10 might cost less than printing them yourself.

3D printing shines for custom, low-volume, or complex geometries. For simple, mass-produced items, buying is often cheaper.

Frequently Asked Questions

Is six cents really possible for a 3D print?

Yes, for very small and light objects. For example, a 3-gram print using filament that costs $20 per kg would cost 6 cents in material. However, most prints weigh more, so six cents is on the low end.

Does the calculator include electricity and other costs?

No, it only calculates the cost of the plastic filament. Electricity, printer wear, and your time are not included. To estimate electricity cost, multiply the printer’s power draw (in kW) by the print time (in hours) and your electricity rate per kWh.

What is the cheapest filament type?

Standard PLA is generally the least expensive, often $15–25 per kg from generic brands. ABS and PETG are slightly more, while specialty materials like TPU or composites cost significantly more.

How can I reduce the weight of my print without breaking it?

Lower the infill percentage (10–15% is often enough for non-structural parts), reduce the number of perimeters, and design hollow spaces. For functional parts, test with increasing infill until it meets your strength needs.

Is a six-cent print as strong as a more expensive one?

Not necessarily. Strength depends on material, infill, wall thickness, and layer adhesion, not cost. A cheap PLA print with proper settings can be stronger than an expensive nylon print with poor settings.

Why does my print cost more than the calculator shows?

The calculator only accounts for material. If you include electricity, printer maintenance, failed prints, and your time, the real cost is higher. Also, if you use a lot of support material, the filament used will be more than the model’s weight alone.

Related

Formula used
in t | Print time | min | 45 | 0
in m | Filament used | g | 12 | 0
in c | Filament cost per kg | USD | 20 | 0
out cost | Material cost | USD | (m / 1000) * c | 2
out efficiency | Cost per hour | USD/h | ((m / 1000) * c) / (t / 60) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.