ThisCalculator

Everyday

NAS Data Scrubbing: Why Smart Tests Aren’t Enough

Updated · Standard formula, shown below

Estimated scrub time (hours) 11.1 hours
Scrub frequency per year
12.2 times/year
Result
Interval (days)
30 days
You entered
Drive size (TB)
8 TB
You entered

Smart tests alone cannot protect your NAS from silent data corruption, because they only detect failing hardware, not the bit rot that occurs on healthy drives. Data scrubbing actively reads every block on your drives and verifies it against stored checksums, repairing or flagging any discrepancies before they become unrecoverable. This article explains why scrubbing is essential, how it works, and how to set it up on your NAS.

Formula

The calculator estimates the time to complete a full data scrub based on drive size and sustained read speed. The formula is:

Scrub time (hours) = (Drive size in TB × 1,000,000 MB) / (Read speed in MB/s × 3600 seconds/hour)

Variables:

  • Drive size (TB) – the raw capacity of the drive in terabytes (1 TB = 1,000,000 MB).
  • Read speed (MB/s) – the sustained sequential read speed of the drive in megabytes per second. Real-world speeds are often lower than the advertised maximum, especially for HDDs.

The result is the minimum time in hours to read every sector once. The second output shows how many scrubs per year your chosen interval yields.

Worked Example

Using the default values: an 8 TB drive with a sustained read speed of 200 MB/s, and a scrub interval of 30 days.

  • Drive size in MB: 8 TB × 1,000,000 = 8,000,000 MB
  • Read per second: 200 MB/s
  • Seconds needed: 8,000,000 / 200 = 40,000 seconds
  • Hours: 40,000 / 3600 = 11.1 hours

So a full scrub takes about 11.1 hours. The frequency is 365 / 30 = 12.2 times per year. Most NAS systems let you schedule scrubs during off-peak hours, so this is usually acceptable.

What Smart Tests Actually Do

S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a diagnostic system built into hard drives and SSDs. It monitors metrics like reallocated sectors, spin-up time, temperature, and read error rates. The NAS can run two types of tests:

  • Short test – a quick check of drive health, usually taking a few minutes, that samples a small portion of the disk.
  • Extended test – a full surface scan that reads every sector, which can take many hours.

However, S.M.A.R.T. only tells you if the drive itself is failing. It does not detect data corruption that occurs on a healthy disk. For example, a bit can flip due to cosmic rays, electrical interference, or gradual magnetic decay. S.M.A.R.T. won’t see that because it doesn’t check the data content—it only checks the drive’s mechanical and electronic health.

What Is Data Scrubbing?

Data scrubbing is a process that reads all data blocks on a storage system and verifies them against a checksum (usually a CRC or a hash like SHA-256). If a mismatch is found, the system attempts to repair the data using redundancy from RAID or a filesystem like ZFS or Btrfs. If no redundancy is available, it flags the error so you can restore from backup.

Scrubbing is not the same as a S.M.A.R.T. extended test. While an extended test only reads the surface to check for bad sectors, a scrub reads the actual data and validates it. A drive can pass a S.M.A.R.T. test with flying colors while still having corrupted files.

Why Scrubbing Is Critical for Data Integrity

Silent data corruption is rare but real. Studies have shown that on large storage systems, a small percentage of blocks will develop errors over time. Without scrubbing, these errors go unnoticed until you try to read the file—and by then, the original data may be gone. Scrubbing catches errors early, when they are still repairable.

For RAID arrays, scrubbing is especially important. If a drive fails and you rebuild the array, any existing corruption on the remaining drives will be propagated to the new drive. Scrubbing before a failure ensures that the data on all drives is consistent, reducing the risk of a failed rebuild.

How to Set Up Data Scrubbing on Your NAS

Most NAS operating systems have built-in scrubbing features. Here’s how to enable them on common platforms:

  • Synology DSM – Go to Storage Manager → RAID Group → Data Scrubbing. You can schedule it monthly or quarterly.
  • QNAP QTS – Open Storage & Snapshots → Storage → Storage/Snapshots → Manage → Action → Check File System. Or use the “RAID Scrubbing” option.
  • TrueNAS (ZFS) – Go to Storage → Pools → the pool’s gear icon → Scrub. You can set up a periodic scrub task under Tasks → Scrub Tasks.
  • Unraid – Use the “Check Disk” feature or run the mdcmd command. Unraid also has a parity check that acts as a scrub.

If you’re running a custom Linux NAS, you can use filesystem tools like zpool scrub for ZFS or btrfs scrub for Btrfs.

Common Mistakes and Misconceptions

One common mistake is thinking that a S.M.A.R.T. extended test replaces a scrub. As explained, they serve different purposes. Another is running scrubs too frequently, which can wear out drives, especially SSDs. Once a month is a good default for most home users. For enterprise systems, weekly scrubs may be appropriate.

Another misconception is that scrubbing is only needed on RAID systems. Even a single drive can benefit from scrubbing if the filesystem supports checksums (e.g., Btrfs or ZFS). Without redundancy, the scrub can only detect errors, not repair them, but detection is still valuable because it alerts you to restore from backup.

Scrubbing vs. S.M.A.R.T. Extended Test

To clarify the difference, consider this analogy: S.M.A.R.T. is like a doctor checking your vital signs—heart rate, blood pressure. A scrub is like a proofreader checking every word in a book for typos. Both are useful, but they catch different problems. A drive can have perfect vital signs yet contain corrupted data.

In practice, you should run both: a S.M.A.R.T. extended test monthly and a data scrub monthly. They can be scheduled on different days to spread the load.

Costs and Performance Impact

Scrubbing consumes I/O bandwidth, which can slow down normal NAS operations. On a busy system, it’s best to schedule scrubs during idle hours (e.g., 2 AM). The time it takes depends on drive size and speed—our calculator gives an estimate. For large arrays, scrubbing can take over 24 hours.

There is also a small risk of finding errors that you cannot repair, which is why you should always have a backup. Scrubbing is not a substitute for backups; it’s a complement.

Frequently Asked Questions

Can data scrubbing damage my drives?

No, scrubbing only reads data. It doesn’t write anything except when it repairs a corrupted block, which is a minimal write. The process is safe and doesn’t harm healthy drives.

How often should I run a data scrub?

For most home users, once a month is sufficient. If you have critical data, you can run it weekly. Avoid running it too frequently (e.g., daily) to reduce wear on drives.

Does scrubbing work on SSDs?

Yes, but SSDs have different failure modes. Scrubbing can help detect data degradation in NAND cells. However, SSDs have limited write endurance, so scrubbing frequency should be lower—maybe every few months.

What happens if the scrub finds an error it can’t fix?

The system will log the error and alert you. The affected file may be unreadable, so you should restore it from backup. If the error is on a RAID array, the system will attempt to rebuild the data from parity or mirror.

Is scrubbing the same as a RAID rebuild?

No. A RAID rebuild is performed after a drive fails to restore redundancy. Scrubbing is a routine maintenance task that checks data integrity. They are complementary, not interchangeable.

Can I use my NAS while scrubbing?

Yes, but performance may be degraded. Most NAS systems allow scrubbing to run in the background with adjustable priority. For critical applications, schedule scrubs during off-hours.

Related

Formula used
in t | Interval (days) | days | 30 | 1
in d | Drive size (TB) | TB | 8 | 1
in s | Read speed (MB/s) | MB/s | 200 | 10
out h | Estimated scrub time (hours) | hours | (d * 1000000) / (s * 3600) | 1
out w | Scrub frequency per year | times/year | 365 / t | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.