Rust CCTV Camera Codes: Full List & Setup Guide

This guide lists every CCTV camera code in Rust and explains how to set up a working surveillance system, from placing the camera to wiring it to a computer station. You’ll get the full code list, the exact steps to view and control cameras, and answers to common questions about range, power, and security.

What Are CCTV Camera Codes?

In Rust, CCTV cameras are placed like other deployables, but you need a code to view their feed. Each camera has a unique 4-digit code, printed on the side of the camera when you look at it. These codes are random per server and per placement, so you cannot memorize a global list. The code is only visible to players who are close enough to read it, and it stays the same until the camera is destroyed and re-placed.

Complete List of Camera Codes

There is no fixed list of codes because they are generated randomly for each camera instance. However, the game does have a set of preset camera locations on the map (e.g., at monuments, roads, and safe zones) that also have random codes. The only way to get a code is to physically visit the camera and read it. Some community servers may use a plugin to assign fixed codes, but that is not part of the vanilla game.

How to Set Up a CCTV Camera System

Setting up a basic system involves three steps: crafting, placing, and connecting.

1. Craft the camera – You need 1 CCTV camera (crafted with 1 tech trash, 1 metal pipe, and 1 targeting computer). You also need a computer station (1 tech trash, 1 metal pipe, 1 circuit board, and 1 metal spring).
2. Place the camera – Aim at a wall, ceiling, or floor and press the deploy button. The camera will attach to the surface. Make sure it has a clear view of the area you want to monitor.
3. Read the code – Walk up to the camera and look at it. The code is displayed in the middle of the screen, usually in white text. Write it down or memorize it.
4. Place a computer station – Place it on a flat surface (like a table or floor). You need to be within about 25 meters of the computer station to interact with it.
5. Connect to the camera – Open the computer station (press E). In the menu, you will see a list of available cameras. Click the one that matches the code you wrote down. The camera feed will appear on the screen.

You can connect to multiple cameras from the same computer station, but you can only view one feed at a time. To switch, just click another camera in the list.

How to View and Control Cameras

Once connected, you can control the camera’s pan and tilt using the mouse or the WASD keys. The camera has a limited field of view, so you may need to rotate it to see different angles. You can also zoom in and out with the mouse wheel. The camera feed is real-time, and there is no recording feature in vanilla Rust.

To disconnect, press the “Disconnect” button or simply walk away from the computer station. The camera will keep its last position until someone else connects.

Common Problems and Fixes

Here are the most frequent issues players encounter:

• Camera code not showing – Make sure you are close enough. The code only appears within about 3 meters. If you are too far, move closer.
• Camera not in the list – The computer station only shows cameras that are within a certain range (about 100 meters). If the camera is too far, you won’t see it. You may need to place a relay or use a modded server that extends the range.
• Camera feed is black – The camera may be destroyed or out of power. Check the camera’s health and make sure it is not blocked by a wall or rock.
• Can’t place the camera – You need to be in a building privilege zone (your base). Cameras cannot be placed on unowned ground.
• Computer station not working – It needs to be placed on a flat surface and within your building privilege. Also, make sure it is not blocked by another deployable.

Range and Power Requirements

CCTV cameras do not require external power. They run on their own internal battery, so you don’t need to wire them to a power source. However, they do have a limited range for the video signal. The computer station can only receive feeds from cameras within about 100 meters. If you need to monitor a larger area, you can place multiple cameras and switch between them, but you cannot view them all at once.

The camera’s view range is about 100 meters, but the image quality degrades with distance. You can zoom in to see farther, but the image becomes pixelated.

Safety and Security Tips

Using CCTV cameras can improve your base security, but they also have risks:

• Camera codes are visible – Anyone who walks up to your camera can read the code and view your feed. To prevent this, place cameras in hard-to-reach areas or inside your base.
• Cameras can be destroyed – They are fragile and can be broken with a few hits. Consider placing them behind reinforced walls or in high places.
• Computer station is a target – If raiders find your computer station, they can view all your cameras. Place it in a secure room.
• Use multiple cameras – Cover all entrances and blind spots. You can place cameras outside and inside your base.

Alternatives to CCTV Cameras

If you want surveillance without the hassle of codes, consider these alternatives:

• Security cameras (modded) – Some servers have plugins that allow you to view cameras without codes, or even record footage.
• Motion sensors – These can alert you to intruders, but they don’t provide video.
• Listening devices – Not in vanilla Rust, but some mods add them.
• Manual patrol – Sometimes the best security is a well-armed player.

Frequently Asked Questions

Can I change the camera code?

No, the code is randomly generated when the camera is placed and cannot be changed. The only way to get a new code is to destroy the camera and place a new one.

How far can a CCTV camera see?

The camera has a render distance of about 100 meters. Objects beyond that will not appear in the feed. You can zoom in, but the image will be low resolution.

Do CCTV cameras need electricity?

No, they have an internal battery that lasts indefinitely. They do not need to be connected to a power grid.

Can I view cameras from my phone or tablet?

No, you can only view cameras through a computer station in the game. There is no remote viewing feature in vanilla Rust.

Why can’t I see my camera in the computer station list?

The computer station only lists cameras within about 100 meters. If your camera is farther away, you won’t see it. Also, make sure the camera is not destroyed and that you are within the computer station’s interaction range (about 25 meters).

Can I record CCTV footage?

No, the game does not have a built-in recording feature. You would need to use external screen recording software if you want to capture footage.

Related

• Token Comparison Prefix Leak: How It Works
• Recover ZIP Files from Android: 7 Ways That Work
• iOS 16 Full Screen Music Player on Lock Screen