ThisCalculator

Everyday

Remove Samsung Monitor Stand Safely: Model Method

Updated · Standard formula, shown below

Remove Samsung Monitor Stand Safely: Model Method

To remove a Samsung monitor stand safely, you must first identify your monitor’s model and use its specific release mechanism—either a set of visible screws, a quick-release button, or a clip-and-slide latch. This article explains the three main methods Samsung uses across its current monitor lines, how to find your exact model, and the step-by-step procedure for each, including the safety precautions that prevent panel damage.

Why the Method Depends on Your Model

Samsung does not use one universal stand attachment. Over the past decade, the company has shipped three distinct mounting systems:

  • Screw-based (older and budget models): The stand neck attaches to the VESA plate with 4 screws, often hidden behind a plastic cover or a snap-on rear panel.
  • Quick-release button (mid-range and many 2020–2024 models): A spring-loaded button or lever sits at the back of the stand neck; pressing it releases a locking hook.
  • Clip-and-slide (ultra-slim and some 2023–2025 models): The stand slides into a slot on the monitor’s rear and clicks into place; removal requires sliding a latch while pulling the stand downward.

Using the wrong method—for example, forcing a screw-based stand to release by pressing a button that doesn’t exist—can strip threads, crack the rear housing, or damage the panel’s internal connectors. Always confirm the method before applying any force.

Find Your Exact Model Number First

Your monitor’s model number is printed on a label on the back of the panel, usually near the input ports or on the bottom edge. It looks like LS27B610EWN or S32BM500U. The first two letters after the size (e.g., “S� for Smart, “B� for Business, “T� for TV-style) often hint at the stand type, but the only reliable way is to search that exact model number on Samsung’s support site or your regional manual. If the label is worn, you can also find the model in the monitor’s on-screen display (OSD) under Support → Information or About. Do not rely on the box or a sticker on the stand—those may be generic.

General Safety Preparation (All Models)

Before touching the stand, take these steps to avoid injury and damage:

  1. Power off the monitor and unplug both the power cable and any connected video cables (HDMI, DisplayPort, USB-C).
  2. Lay the monitor face-down on a clean, soft, flat surface—use a thick towel, foam pad, or the original styrofoam. The screen surface must not bear any weight.
  3. If the stand has a removable base plate, detach it first (usually a single thumbscrew or a quick-release tab) so the neck is the only part attached.
  4. Work in a well-lit area and keep small screws in a labeled container.
  5. Never pull the stand by the cable management clip or the neck’s plastic trim—grip the metal neck or the base plate.

Method 1: Removing a Screw-Based Stand

This is the most common on 24-inch and 27-inch business models (e.g., S24R350, S27R350, older S24E450). After laying the monitor face-down:

  1. Look for a small plastic cover at the junction of the stand neck and the monitor’s rear. It may have a finger notch or a small hole.
  2. Pry the cover off gently with a plastic spudger or your fingernail. Do not use a metal screwdriver—it will scratch the housing.
  3. Underneath, you’ll see four screws (usually Phillips #2) securing the neck to the VESA plate.
  4. Support the neck with one hand while loosening the screws with the other. Remove all four, then lift the neck straight away from the panel.
  5. If the neck does not come free, check for a fifth screw or a locking tab near the VESA hole—some models have a small latch that must be pushed inward.

After removal, keep the four screws with the stand. If you plan to mount the monitor on an arm, you’ll need the VESA adapter screws that came with the arm (often M4 x 10mm), not the stand screws.

Method 2: Quick-Release Button or Lever

Many 2021–2024 models (e.g., S32BG75, S27A800, S43BM70) use a spring-loaded button. The button is usually on the back of the stand neck, about 2–3 cm below the monitor’s rear panel, and may be labeled with a small “push� icon.

  1. With the monitor face-down, locate the button or lever. It may be covered by a rubber flap or a sliding plastic gate.
  2. Press the button firmly with one hand while holding the neck with the other.
  3. While holding the button, pull the neck straight out of the monitor’s socket. You may feel a slight click as the locking hook disengages.
  4. If the neck does not slide out, do not twist it. Check whether there is a second release—some models require sliding the button sideways rather than pressing it.

This method is the fastest, but also the easiest to get wrong: pressing the button without pulling the neck at the same time can cause the hook to re-engage. If you feel resistance, release the button, re-align the neck, and try again with a smoother simultaneous press-and-pull.

Method 3: Clip-and-Slide (Ultra-Slim and 2023+ Models)

The newest Samsung monitors (e.g., ViewFinity S8 series, Odyssey G5/G6 from 2023 onward) use a slot-and-latch design. There is no button; instead, a sliding latch sits on the stand neck near the top.

  1. Lay the monitor face-down as described.
  2. Look for a small sliding tab or a recessed lever on the neck’s rear, right where the neck meets the panel.
  3. Slide the tab in the direction indicated by a tiny arrow (usually toward the bottom of the monitor).
  4. While holding the tab in the released position, pull the neck downward and away from the panel. The stand should slide out of its rail.
  5. If the neck is stuck, check that the tab is fully slid—some models require a 90-degree twist of the tab before it releases.

This design has no screws and no visible button, so many users mistake it for a fixed stand. The key is to always look for a movable piece on the neck itself, not on the monitor’s rear.

Common Mistakes and How to Avoid Them

  • Forgetting to remove the base plate: The base plate’s weight can bend the neck’s plastic hinge when you pull. Always detach the base first.
  • Using a metal tool to pry covers: This leaves permanent scratches. Use a plastic spudger or a guitar pick.
  • Pulling the stand while the monitor is upright: This puts stress on the panel’s internal connectors. Always lay it flat.
  • Mixing up VESA screw sizes: Stand screws are usually M4 x 12mm; VESA arm screws are often M4 x 10mm. Using the wrong length can damage the panel threads.
  • Not checking for a second release: Some models have both a button and a screw. If you remove the screws but the neck still won’t come off, look for a hidden latch.

What to Do After Removal

Once the stand is off, you have three common paths:

  • Mount on a VESA arm: Most Samsung monitors have a 100x100mm VESA pattern. Attach the arm’s plate with the provided screws, then tighten to the recommended torque (usually 8–12 in-lbs). Over-tightening can crack the panel.
  • Store the stand: Keep the screws in a small bag taped to the stand base. Store the stand upright, not under heavy objects.
  • Use the monitor without a stand: Only do this if you have a VESA arm or a wall mount. Never prop the panel against a wall—it will overheat and may fall.

If you are reattaching the stand later, reverse the steps. For screw-based models, align the neck with the VESA holes, insert screws by hand first, then tighten in a cross pattern (top-left, bottom-right, top-right, bottom-left). For quick-release models, push the neck straight in until you hear a click. For clip-and-slide, slide the neck into the slot until the latch snaps.

Frequently Asked Questions

Do I need to remove the stand to use a VESA mount?

Yes, in most cases. The VESA holes are behind the stand neck. On some Samsung models, you can attach a VESA adapter over the stand, but that is rare and not recommended—the adapter adds thickness and may not align with the panel’s weight distribution.

What if my stand has a screw but no visible cover?

Look for a small rubber plug or a thin plastic seam. Some models hide the screws behind a snap-on panel that requires pressing a release tab on the bottom edge. Gently run a plastic spudger along the seam to find the tab.

Can I remove the stand while the monitor is on?

No. Always power off and unplug. The monitor’s internal power supply can retain a charge, and the panel is fragile. Also, the OSD menu may have a “Stand Removal� warning that appears only when the monitor is off—this is a safety reminder, not a tool.

Why does my Samsung monitor have no release button and no screws?

You likely have a clip-and-slide model. Look for a small latch on the neck itself, often near the top edge. It may be flush with the plastic, so run your finger along the neck’s rear to feel for a movable piece.

Will removing the stand void my warranty?

No, removing the stand is a normal user operation. However, damage caused by improper removal (e.g., cracked housing, stripped threads) is not covered. Follow the manual’s instructions to stay safe.

Is there a risk of the panel cracking if I lay it face-down?

Yes, if the surface has any debris or if you press down on the screen. Use a clean, soft towel and ensure the monitor’s own weight is supported by the bezel edges, not the LCD surface. Avoid placing anything on top of the panel.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.