Rapid Liquid 3D Printing: The Next Big Thing?
- Effective print speed
- cm^3/min
- Result
- Print time
- 30 min
- You entered
- Object diameter
- 5 cm
- You entered
Rapid liquid 3D printing—also called computed axial lithography (CAL)—is a genuinely promising technology that prints an entire object at once from a vat of resin, not layer by layer. It is not yet a mainstream consumer product, but it could be the next big leap in how we make things, especially for medical and industrial parts.
Formula
The calculator above estimates the effective print speed of a rapid liquid 3D printing process. The volume of a sphere is:
V = (4/3) × π × (d/2)³
Where:
- V = volume of the printed object (cm³)
- d = diameter of the object (cm)
- t = total print time (minutes)
The effective print speed is then V / t, expressed in cm³ per minute. This gives a rough measure of how fast the process can produce material, useful for comparing with traditional layer-by-layer printing.
Worked Example
Using the default values: diameter = 5 cm, print time = 30 minutes.
- Radius = 5 / 2 = 2.5 cm
- V = (4/3) × π × (2.5)³ = (4/3) × 3.14159 × 15.625 = 65.45 cm³
- Effective speed = 65.45 / 30 = 2.18 cm³/min
The calculator shows 2.18 cm³/min, matching the manual calculation.
What Is Rapid Liquid 3D Printing?
Traditional 3D printing builds objects layer by layer, which is slow and can leave visible lines. Rapid liquid printing, or volumetric printing, instead solidifies a whole 3D volume at once. The most well-known method is computed axial lithography (CAL), developed by researchers at UC Berkeley and Lawrence Livermore National Laboratory. In CAL, a vat of photosensitive resin is rotated while a projector shines patterns of light from multiple angles. The light patterns overlap, and where the cumulative light dose exceeds a threshold, the resin hardens. After a few seconds to a few minutes, the object is fully formed, and the remaining liquid is drained away. This approach is not just faster—it also allows for objects with internal cavities, overhangs, and complex geometries that are difficult or impossible with layer-based printing.
How It Works: The Science in Simple Terms
The key to CAL is a special resin that only solidifies when it receives enough light energy. The projector sends a series of 2D images into the rotating vat. Each image is like a shadow of the object from a particular angle. As the vat rotates, the light accumulates in the resin. At points where the accumulated dose exceeds the critical threshold, the resin becomes solid. The rest stays liquid and is later removed. This is fundamentally different from stereolithography (SLA), which uses a laser to trace each layer on the surface. CAL is sometimes called “volumetric” because the entire volume is exposed to light simultaneously.
Why It Could Be the Next Big Thing
The main advantage is speed. A typical CAL print of a small object (a few centimeters) takes 30 to 120 seconds, compared to 30 minutes to several hours for layer-based methods. This makes it viable for rapid prototyping, small-batch manufacturing, and even on-demand production in hospitals or repair shops. Another advantage is material properties: because there are no layers, parts are stronger and more isotropic (uniform in all directions). This is critical for load-bearing parts like medical implants or aerospace components. Additionally, the ability to print around existing objects—like a handle around a metal rod—opens new design possibilities. Researchers have already demonstrated printing a tiny model of a human jaw, a screw, and a ball inside a cage, all in one piece without supports.
Current Limitations and Challenges
Despite the promise, there are significant hurdles. The resin chemistry is complex and currently expensive. The light patterns require precise calibration; even slight misalignment can cause failed prints. The build volume is limited—most lab setups can only print objects a few centimeters in diameter. Scaling up to larger parts requires more powerful projectors and more sophisticated optics, which increases cost. Also, the process is currently limited to photopolymers, which are not as strong or heat-resistant as engineering plastics like ABS or nylon. Finally, post-processing is needed: the object must be washed to remove uncured resin and then cured under UV light to achieve full strength. These steps are similar to SLA but still add time and cost.
How to Choose: Rapid Liquid vs. Traditional 3D Printing
If you are considering adopting this technology, here are the factors to weigh:
- Speed requirement: If you need parts in minutes, CAL is superior. If you can wait hours, traditional methods are cheaper.
- Part complexity: For internal channels, moving parts, or complex overhangs, CAL is ideal. For simple brackets, FDM is fine.
- Material properties: If you need high strength or heat resistance, CAL resins are not yet ready. Traditional FDM with engineering filaments is better.
- Cost: CAL machines and resins are expensive. For low-volume production, the cost per part may be higher than injection molding or FDM.
- Post-processing: CAL requires washing and curing, similar to SLA. FDM only needs support removal.
Common Problems and Misconceptions
A common misconception is that rapid liquid printing is just a faster version of SLA. In reality, the physics are different—CAL uses light patterns, not a laser point. Another misconception is that it can print any material. Currently, only photopolymers work, and they are brittle. A frequent problem in CAL is overcuring: if the light dose is too high, the entire vat solidifies. This happens when the projector brightness or exposure time is miscalculated. Also, the resin must be transparent to allow light to pass through; adding pigments or fillers can block light and ruin the print. Finally, the object must be designed with the light exposure in mind—sharp corners may receive extra dose and become distorted.
Safety and Handling
Photopolymer resins are skin irritants and can cause allergic reactions. Always wear nitrile gloves and safety glasses when handling uncured resin. Work in a well-ventilated area because some resins emit volatile organic compounds (VOCs). If resin spills on skin, wash immediately with soap and water, not solvents. Uncured resin is a hazardous waste; do not pour it down the drain. After printing, the part must be washed in isopropyl alcohol or a specialized cleaner, and the used alcohol is also hazardous. Cured parts are generally safe to handle, but sanding may release dust that should not be inhaled. Always follow the resin manufacturer’s safety data sheet (SDS).
Alternatives to Rapid Liquid Printing
If CAL is not yet practical for your use, consider these alternatives:
- FDM (Fused Deposition Modeling): The most common and cheapest. Uses thermoplastic filament. Good for prototyping and functional parts, but has visible layers.
- SLA (Stereolithography): Uses a laser to cure resin layer by layer. Higher resolution than FDM, but slower and requires post-processing.
- DLP (Digital Light Processing): Similar to SLA but uses a projector to cure an entire layer at once. Faster than SLA, but still layer-based.
- Multi-jet Fusion (MJF): Uses a powder bed and fusing agent. Fast and strong, but expensive and only for industrial use.
- Injection Molding: Not 3D printing, but for mass production, it is faster and cheaper per part once the mold is made.
Frequently Asked Questions
How fast is rapid liquid 3D printing compared to normal 3D printing?
For small objects (a few centimeters), CAL can print in 30–120 seconds, whereas FDM or SLA would take 30 minutes to several hours. The speed advantage shrinks for larger parts because the light exposure time increases, but it is still generally faster.
Can I buy a rapid liquid 3D printer for home use?
As of now, no. CAL printers are mainly in research labs and a few startups. They are not commercially available for consumers. The technology is still in development, and the cost is high. Expect to wait a few more years for a desktop version.
What materials can be used in rapid liquid printing?
Only photopolymers (light-curable resins) work. These are similar to SLA resins but must be transparent and have a specific photoinitiator chemistry. They are generally acrylic-based and are not as strong as thermoplastics. Research is ongoing to develop more durable resins.
Is rapid liquid printing better than FDM for mechanical parts?
For strength and isotropy, yes, because there are no layers. However, current resins are brittle and have low heat resistance. For functional parts that undergo stress or heat, FDM with engineering materials like PETG or nylon is often better. CAL is best for complex geometries and medical models.
What are the main safety risks with rapid liquid printing?
The main risks are skin contact with uncured resin, inhalation of VOCs, and fire hazard from the alcohol used in post-processing. Always wear gloves, work in a ventilated area, and store chemicals properly. The printer itself uses a projector, which is safe, but the resin is toxic.
Will rapid liquid printing replace traditional manufacturing?
Not in the near future. It is excellent for prototyping, custom medical implants, and small complex parts, but it cannot match the speed and cost of injection molding for mass production. It will likely complement existing methods rather than replace them.
Related
Formula used
in t | Print time | min | 30 | 0 in d | Object diameter | cm | 5 | 0 out v | Volume | cm^3 | (4/3)*pi*(d/2)^3 | 2 out rate | Effective print speed | cm^3/min | v / t | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.