ThisCalculator

Chemistry

Percent Yield Formula Calculator: How to Use It

Updated · Standard formula, shown below

Percent yield 85.0 %
Actual yield
8.5 g
You entered
Theoretical yield
10 g
You entered

This percent yield calculator works out the percent yield of a chemical reaction from the actual yield and the theoretical yield. You enter the actual mass of product you obtained and the theoretical mass you calculated from the balanced equation, and it returns the percent yield as a percentage. The same formula applies whether you work in grams, kilograms, or any other mass unit, as long as both values use the same unit.

Formula

The percent yield formula is:

Percent Yield = (Actual Yield / Theoretical Yield) × 100%

Where:

  • Actual yield is the mass of product you actually recovered from the reaction (in grams, kg, etc.).
  • Theoretical yield is the maximum mass of product that could form, calculated from the limiting reactant using stoichiometry (same unit as actual yield).

The result is a percentage. A value of 100% means you recovered exactly the theoretical amount; less than 100% means some product was lost; greater than 100% usually indicates impurities, moisture, or measurement error.

Worked Example

Using the default values from the calculator: actual yield = 8.5 g, theoretical yield = 10.0 g.

  1. Divide actual by theoretical: 8.5 ÷ 10.0 = 0.85
  2. Multiply by 100 to get a percentage: 0.85 × 100 = 85%

The calculator gives 85.0%, which matches.

Why Percent Yield Matters in Chemistry

Percent yield tells you how efficient a reaction is. In a perfect world, you would get every gram of product the equation predicts, but in practice you lose material during transfer, filtration, recrystallization, or because side reactions occur. A low percent yield means you are wasting reactants and time; a high one means your procedure is efficient. Chemists routinely report percent yield in lab reports and research papers to show how well a synthesis worked.

It also helps in scaling up: if a lab-scale reaction gives 75% yield, you can estimate how much product a larger batch will produce, assuming the same efficiency.

How to Calculate Theoretical Yield

Before you can use the percent yield formula, you need the theoretical yield. Here are the steps:

  1. Write a balanced chemical equation for the reaction.
  2. Convert the mass of each reactant to moles using its molar mass.
  3. Identify the limiting reactant – the one that produces the fewest moles of product.
  4. Use the mole ratio from the balanced equation to find the moles of product expected.
  5. Convert moles of product to mass using the product’s molar mass.

For example, if you start with 5.0 g of sodium carbonate (molar mass 105.99 g/mol) and excess hydrochloric acid, the theoretical yield of sodium chloride (molar mass 58.44 g/mol) from the reaction Na₂CO₃ + 2HCl → 2NaCl + CO₂ + H₂O is:

  • Moles Na₂CO₃ = 5.0 / 105.99 = 0.0472 mol
  • Moles NaCl = 0.0472 × 2 = 0.0944 mol
  • Theoretical yield = 0.0944 × 58.44 = 5.52 g

If you actually recovered 4.10 g, your percent yield is (4.10 / 5.52) × 100 = 74.3%.

Common Mistakes and How to Avoid Them

The most frequent errors when calculating percent yield are:

  • Unit mismatch: Using actual yield in grams and theoretical yield in milligrams. Always convert to the same unit first.
  • Using the wrong reactant: If you have multiple reactants, you must use the limiting reactant to find theoretical yield, not just the one you have the most of.
  • Forgetting to multiply by 100: The formula gives a decimal (0.85); you must multiply by 100 to get a percentage.
  • Rounding too early: Rounding intermediate values can change the final percentage. Keep extra digits until the end.
  • Confusing percent yield with percent error: Percent error compares a measured value to a true value, while percent yield compares actual to theoretical product. They are different.

Also note that a percent yield over 100% is not automatically an error – it often means the product is wet or contains impurities. Dry and purify the sample before weighing.

When Percent Yield Is Not Useful

Percent yield is meaningful only for reactions that go to completion and have a single, isolable product. It is less useful when:

  • The reaction is reversible and reaches equilibrium (like esterification) – the theoretical yield is not the maximum possible under those conditions.
  • Multiple products form (e.g., combustion) and you only isolate one.
  • You are measuring a gas that escapes – you cannot weigh it directly.

In those cases, chemists use other measures like conversion (how much reactant was consumed) or selectivity (how much of the desired product formed relative to all products).

Frequently Asked Questions

What if my percent yield is above 100%?

It usually means your product is not pure – it contains water, solvent, or unreacted starting material that adds mass. Dry the product thoroughly and reweigh. If it is still above 100%, check your theoretical yield calculation for errors, such as using the wrong limiting reactant or molar mass.

Can I use moles instead of grams in the formula?

Yes, as long as both actual and theoretical yields are in moles. The formula is unit-agnostic; it just requires the same unit for both. However, in practice you weigh solids in grams, so you usually convert moles to mass first.

What is a good percent yield?

There is no universal cutoff. In undergraduate labs, yields above 70% are often considered good, but some reactions naturally give lower yields. A reaction with 50% yield can still be valuable if the product is hard to make. The key is to report the yield honestly and explain any losses.

How do I find theoretical yield if I have two reactants?

Calculate the moles of product each reactant would produce if it were entirely consumed. The reactant that gives the smaller amount is the limiting reactant, and that smaller amount is your theoretical yield. The other reactant is in excess.

Does percent yield change with scale?

Not in theory, but in practice it often does. Small-scale reactions lose a higher fraction to transfer and handling, so yields may be lower. Larger batches can sometimes give higher yields because relative losses are smaller, but side reactions may also become more significant. Always report the yield for the actual scale you used.

What is the difference between percent yield and percent recovery?

Percent recovery is used in purification (like recrystallization) and compares the mass after purification to the mass before. Percent yield is used in synthesis and compares the actual product mass to the theoretical maximum from the reaction. They are calculated the same way but answer different questions.

Related

Formula used
in actual | Actual yield | g | 8.5 | 0
in theo | Theoretical yield | g | 10.0 | 0
out py | Percent yield | % | actual / theo * 100 | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.