ThisCalculator

Everyday

No Signal on Monitor? Fixes That Work

Updated · Standard formula, shown below

If your monitor shows “No Signal” when the computer is on, the display cable or input selection is usually the culprit. This guide walks you through the most common causes and fixes, from reseating cables to updating drivers, so you can get your screen back quickly.

What “No Signal” Actually Means

The monitor is powered and receiving electricity, but it isn’t receiving video data from the computer. This is different from a black screen with a power LED off, which indicates a power problem. The monitor’s on-screen display (OSD) is working, but the video input is empty. The message can appear on any type of display—LCD, LED, or OLED—and with any connection: HDMI, DisplayPort, DVI, or VGA.

Quick Checks Before Diving In

Start with the simplest possibilities. They account for a surprising number of cases.

  • Is the monitor on the correct input? Press the “Input” or “Source” button on the monitor and cycle through HDMI, DisplayPort, DVI, and VGA. Many people have a monitor with multiple ports and the wrong one selected.
  • Is the computer actually running? Listen for fans, look for power LEDs. If the PC is in sleep mode, press a key or move the mouse. A quick press of the power button on the computer (not a long press) can wake it.
  • Is the cable fully inserted at both ends? Unplug and firmly re-plug the video cable. A loose connection is extremely common, especially with DisplayPort cables that have a small latch.
  • Try a different cable. Cables can fail internally even if they look fine. If you have a spare HDMI or DisplayPort cable, swap it in.

Step-by-Step Troubleshooting

If the quick checks don’t work, proceed through these steps in order. Each step addresses a different layer of the problem.

  1. Reseat the video cable and power cycle the monitor. Unplug the cable from both ends, wait 30 seconds, and plug it back in. Then turn off the monitor, unplug its power cord, wait 60 seconds, and plug it back in. This clears any temporary glitch in the monitor’s firmware.
  2. Test with a different port on the computer. If your graphics card has multiple HDMI or DisplayPort outputs, try another one. If you have integrated graphics (ports on the motherboard), try those, but note that they may be disabled if a dedicated GPU is installed.
  3. Boot into Safe Mode. If the signal appears during the BIOS/UEFI screen but disappears when Windows loads, a driver or startup program is likely at fault. Restart the PC and press F8 (or Shift+F8) repeatedly, or use the Windows Recovery Environment to boot into Safe Mode. If the display works in Safe Mode, the issue is a driver or software conflict.
  4. Update or reinstall the graphics driver. A corrupted or outdated GPU driver can cause a “No Signal” error after the boot screen. In Safe Mode, use Device Manager to uninstall the display adapter, then restart. Windows will reinstall a basic driver. Then download the latest driver from the GPU manufacturer’s website (NVIDIA, AMD, or Intel).
  5. Check the GPU is seated properly (desktop PCs). If you have a dedicated graphics card, power off the PC, open the case, and press the card firmly into its PCIe slot. Also check that the power connectors (6-pin or 8-pin) are secure. A partially seated GPU will not send a signal.
  6. Reset the BIOS/UEFI. A misconfigured BIOS setting (like a wrong primary display output) can cause no signal. Clear the CMOS by removing the round battery on the motherboard for a minute, or use the motherboard’s jumper. This resets all settings to defaults.
  7. Test the monitor with another device. Connect a laptop, game console, or another PC to the monitor. If it works, the monitor is fine and the problem is in your computer. If it still says “No Signal,” the monitor or cable is the problem.

Common Causes and Their Fixes

Here are the most frequent underlying reasons, beyond the generic steps.

  • Wrong input selected: The monitor is on HDMI 1 but the PC is connected to HDMI 2. Fix: cycle inputs.
  • Faulty or incompatible cable: A damaged cable, or a cable that is too long (over 15 meters for HDMI), can drop signal. Fix: use a shorter, high-quality cable.
  • GPU driver crash: A driver that has stopped responding can leave the display blank. Fix: restart the PC, or use Windows key + Ctrl + Shift + B to restart the graphics driver.
  • Power supply issues: If the GPU doesn’t get enough power, it won’t output video. Fix: check that the PSU is adequate and that all power connectors are attached.
  • Monitor hardware failure: The monitor’s input board can fail. Fix: test with another device. If it fails there, the monitor needs repair or replacement.

Understanding DisplayPort and HDMI Specifics

Different cables have different quirks. DisplayPort has a latch that can be partially engaged, causing a loose connection. Also, some DisplayPort cables have a small clip that, if not fully pushed in, will not make contact. HDMI is more forgiving but can be finicky with long runs. For high refresh rates (144Hz or higher), you need a cable that supports the bandwidth—an older HDMI cable may not handle 1440p at 144Hz, resulting in no signal. Always check the cable’s spec against your monitor’s resolution and refresh rate.

When It’s a Hardware Problem

If you’ve tried all the steps and the monitor still shows “No Signal” on a known-good device, the issue is likely internal hardware. The most common failures are:

  • GPU failure: The graphics card has died or is overheating. Fix: try a different GPU if you have one.
  • Motherboard failure: The PCIe slot or the board itself is faulty. Fix: test the GPU in another slot or board.
  • Monitor failure: The monitor’s logic board or panel is broken. Fix: professional repair or replacement.

In these cases, there is no software fix. If the PC boots but shows no signal, and you’ve tested the monitor with another device, the GPU or motherboard is the prime suspect.

Frequently Asked Questions

Why does my monitor show “No Signal” but the PC is on?

This usually means the monitor isn’t receiving data from the computer. It could be a loose cable, wrong input, a GPU driver crash, or a hardware failure. Start with the cable and input checks, then move to Safe Mode.

Can a bad HDMI cable cause “No Signal”?

Yes. A damaged or low-quality HDMI cable can fail to transmit the signal, especially at high resolutions or refresh rates. Try a different cable, preferably a shorter one, to rule this out.

How do I fix “No Signal” when my computer boots?

If you see the BIOS screen but then lose signal, it’s a driver issue. Boot into Safe Mode and update or roll back your graphics driver. If you never see the BIOS, it’s a hardware or cable issue.

Why does my monitor say “No Signal” after waking from sleep?

This is often a power management or driver issue. Try disabling fast startup in Windows, updating your GPU driver, and checking that the monitor’s power settings are set to not turn off completely. Also, try a different cable.

Is “No Signal” a monitor or computer problem?

It could be either. To isolate, connect the monitor to another device (like a laptop). If it works, the monitor is fine. If not, the monitor is faulty. If the monitor works, the problem is in your computer’s GPU, cable, or software.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.