ThisCalculator

Everyday

No EFI System Partition Found: Fixes & Causes

Updated · Standard formula, shown below

“No EFI system partition was found” is a Windows Setup error that appears when the installer cannot locate the GPT partition with the EFI System Partition (ESP) required to boot in UEFI mode. The fix is to either create the missing ESP on the target disk or switch the firmware to legacy BIOS mode, depending on your hardware and preference. Below is a detailed breakdown of why this happens and exactly how to resolve it.

What Is the EFI System Partition?

The EFI System Partition is a small, FAT32-formatted partition on a GPT disk that stores boot loaders, drivers, and data used by the UEFI firmware to start Windows. It is typically 100–500 MB and has no drive letter assigned, so it is invisible in File Explorer. On a standard Windows installation, the ESP is created automatically when you install to an unallocated disk in UEFI mode. If that partition is missing, corrupt, or on a different disk, the installer refuses to continue.

Why Does This Error Occur?

The most common causes are:

  • Installing to a disk with no ESP – The target disk is GPT but lacks an EFI System Partition, often because it was previously used with a legacy BIOS setup or was partitioned manually.
  • Booting the installer in the wrong mode – You booted the USB drive in legacy BIOS mode, so Windows Setup tries to install in BIOS mode, but the disk is GPT. The reverse also happens: UEFI boot with an MBR disk.
  • Multiple disks with conflicting partition styles – The installer may be looking at a different disk than the one you selected, or the disk has an MBR partition table that cannot hold an ESP.
  • Corrupted or missing ESP – A previous failed installation, disk cleanup, or third-party partitioning tool may have deleted or damaged the ESP.

Method 1: Create the ESP Using Diskpart

This is the most reliable fix when you want to keep UEFI mode and the disk is already GPT. You will use the Command Prompt from Windows Setup.

  1. At the “No EFI system partition was found” screen, press Shift+F10 to open Command Prompt.
  2. Type diskpart and press Enter.
  3. Type list disk to see all disks. Note the disk number of the target disk (e.g., Disk 0).
  4. Type select disk 0 (replace 0 with your disk number).
  5. Type list partition to see existing partitions. If the disk has unallocated space, you can create the ESP there.
  6. To create a new ESP, type create partition efi size=100 (size in MB). This creates a 100 MB ESP.
  7. Type format quick fs=fat32 to format it as FAT32.
  8. Type assign letter=S to give it a temporary letter (optional).
  9. Type exit and close Command Prompt.
  10. Click Refresh in the installer and retry the installation.

If the disk already has an ESP but it is not being recognized, you can also use list partition to find it (it will have type “System” in the “Type” column). Select that partition and assign a letter, then exit and refresh.

Method 2: Convert the Disk to GPT or MBR

If the disk is MBR and you want UEFI, you must convert it to GPT. This erases all data, so back up first. In Diskpart:

  1. Follow steps 1–4 above to select the disk.
  2. Type clean to remove all partitions (this deletes everything).
  3. Type convert gpt to change the partition table.
  4. Exit and restart the installer. Windows will now create the ESP automatically.

If you prefer to stay with legacy BIOS (MBR), you can instead boot the USB in legacy mode and convert the disk to MBR with convert mbr. However, modern hardware and Windows 11 require UEFI, so GPT is the recommended path.

Method 3: Boot the Installer in the Correct Mode

Often the error is simply a boot-mode mismatch. Restart your computer, enter the boot menu (usually F12, F11, or Esc during startup), and choose the USB drive entry that says UEFI or has the prefix “UEFI:”. If you see two entries for the same USB, pick the one with UEFI. Then delete any existing partitions on the target disk during setup and let Windows create the ESP automatically. This works only if the disk is GPT; if it is MBR, you will get a different error about MBR/GPT.

Common Mistakes and Misconceptions

  • “I already have an ESP, why does it still fail?” – The ESP must be on the same disk as the Windows partition. If you have an ESP on Disk 0 but install to Disk 1, the installer may still complain. Ensure the ESP is on the target disk.
  • “I can just format the whole disk and it will work.” – Formatting a GPT disk does not create an ESP. You must either let Windows create it during a clean install or create it manually with Diskpart.
  • “FAT32 is required.” – Yes, the ESP must be FAT32. NTFS will not work for UEFI boot.
  • “The ESP can be any size.” – It must be at least 100 MB for Windows. Some tools create 32 MB, which is too small.

When to Use Legacy BIOS Instead

If your computer is older and does not support UEFI, or if you have a reason to stay with MBR (e.g., dual-booting with an old OS), you can switch the firmware to legacy mode. In the BIOS/UEFI settings, find the boot mode option (often under “Boot” or “Storage”) and set it to Legacy or CSM. Then boot the USB in legacy mode and the installer will not look for an ESP. However, Windows 11 requires UEFI, so this is only viable for Windows 10 or earlier.

Frequently Asked Questions

Will this error erase my data?

No, the error itself does not erase data. However, some fixes, like converting the disk to GPT with clean, will erase everything. Always back up important files before attempting any disk-partition changes.

Can I install Windows on an MBR disk without an ESP?

Yes, but only if you boot in legacy BIOS mode. In UEFI mode, Windows requires a GPT disk with an ESP. The installer will refuse to continue if the disk is MBR.

How do I check if my disk is GPT or MBR?

In Diskpart, type list disk. Look at the “Gpt” column – an asterisk (*) means GPT, blank means MBR. You can also use the Disk Management tool in Windows, but that is not available during setup.

What if I don’t have a Command Prompt option?

Shift+F10 works on most Windows Setup screens. If it does not, you can also use “Repair your computer” > “Troubleshoot” > “Command Prompt” from the installer’s first screen.

Is 100 MB ESP enough for Windows 11?

Yes, 100 MB is the minimum and works fine for Windows 11. Some systems use 300–500 MB, but that is not required. If you plan to use BitLocker, a slightly larger ESP (e.g., 300 MB) can be helpful, but 100 MB still works.

Can I create the ESP after Windows is installed?

Yes, but it is more complex. You would need to use a tool like Diskpart to create the ESP, then use bcdboot to copy boot files. It is much easier to fix the issue during installation.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.