ThisCalculator

Everyday

Marvel Rivals Best Settings for FPS & Visibility

Updated · Standard formula, shown below

Average pace 5.00 min/km
Average speed
12.00 km/h
Result
Finish time
50 min
You entered
Distance
10 km
You entered

To get the best competitive settings in Marvel Rivals, prioritize a high and stable frame rate over visual fidelity: set the Display Mode to Fullscreen, cap your FPS to your monitor’s refresh rate (or leave it uncapped if your GPU can sustain it), and set the overall graphics quality to Low or Medium. This reduces input lag and makes enemy silhouettes and projectiles easier to track, which matters more than shadows or reflections in a fast-paced hero shooter.

Formula

The calculator above works out your average running pace and speed from the time you took to cover a known distance. The formulas are:

  • Pace (min/km) = Finish time (minutes) ÷ Distance (km)
  • Speed (km/h) = Distance (km) ÷ (Finish time (minutes) ÷ 60)

Where:

  • Finish time (t) – the total time you ran, in minutes (e.g., 50 minutes).
  • Distance (d) – the distance you covered, in kilometers (e.g., 10 km).
  • Pace – the number of minutes it takes you to run one kilometer. A lower pace means you are running faster.
  • Speed – the average speed in kilometers per hour. A higher speed means you are running faster.

Worked Example

Using the default values from the calculator: you finish a 10 km run in 50 minutes.

  1. Calculate pace: 50 minutes ÷ 10 km = 5.0 min/km.
  2. Calculate speed: 10 km ÷ (50 ÷ 60) = 10 ÷ 0.8333 = 12.0 km/h.

So your average pace is 5:00 min/km and your average speed is 12.0 km/h. The calculator gives the same result, rounded to 2 decimals.

Why Use This Calculator

Runners use pace and speed to plan training, set realistic race goals, and measure improvement. If you know you can hold a certain pace, you can estimate your finish time for a longer distance. For example, a 5:00 min/km pace over a marathon (42.195 km) would give a finish time of about 3 hours 31 minutes. Conversely, if you have a target finish time, you can work backward to find the pace you need to train at.

How to Read the Results

The pace result is shown in minutes per kilometer (min/km). A pace of 5.0 means 5 minutes and 0 seconds per kilometer. The speed result is in kilometers per hour (km/h). In countries that use miles, pace is often shown as minutes per mile. To convert, multiply the pace in min/km by 1.609 to get min/mile, or divide the speed in km/h by 1.609 to get mph.

Common Mistakes

  • Mixing units: If you enter your distance in miles but the calculator expects kilometers, your pace will be wrong. Always convert miles to kilometers (1 mile = 1.609 km) before entering.
  • Using seconds instead of minutes: If you ran for 50 minutes and 30 seconds, enter 50.5 minutes, not 50.30. The calculator treats the input as a decimal number of minutes.
  • Rounding too early: Rounding the pace to one decimal (e.g., 5.0) is fine for most training, but for race planning, keep two decimals to avoid small errors that add up over long distances.

Limitations of the Formula

This calculator gives your average pace and speed over the whole run. It does not account for elevation gain, terrain, wind, or stops. If you run on hills or trails, your actual effort per kilometer will vary. Also, the formula assumes you ran at a steady effort; if you did intervals or walked, the average pace will not reflect your true running ability.

Frequently Asked Questions

How do I convert my pace from min/km to min/mile?

Multiply the pace in minutes per kilometer by 1.609. For example, a 5:00 min/km pace is 5 × 1.609 = 8:03 per mile. Alternatively, divide your speed in km/h by 1.609 to get miles per hour.

What is a good running pace for a beginner?

There is no single “good” pace because it depends on age, fitness, and gender. A common benchmark for a recreational runner is a 6:00–7:00 min/km pace for a 5 km run. If you can run 5 km in 30 minutes, your pace is 6:00 min/km. Focus on effort and consistency rather than a specific number.

Can I use this calculator for walking?

Yes. The formula works for any activity where you cover a distance in a known time. A typical walking pace is 10–12 min/km (about 5–6 km/h). Just enter your walking time and distance.

How do I calculate my finish time for a race?

Multiply your target pace (in min/km) by the race distance (in km). For example, if you want to run a 10 km at 5:30 min/km, your finish time is 5.5 × 10 = 55 minutes. This calculator can help you find the pace if you already have a target time.

Does the calculator account for elevation or stops?

No. It only uses total time and distance. If you stop for water or run on hills, your actual running effort will be higher than the average pace suggests. For a more accurate training load, use a GPS watch that tracks elevation and heart rate.

Related

Formula used
in t | Finish time | min | 50 | 0
in d | Distance | km | 10 | 0
out pace | Average pace | min/km | t / d | 2
out speed | Average speed | km/h | d / (t / 60) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.