Mac Sequoia External Drives Not Mounting? Fixes
If your external drive isn’t showing up on your Mac after updating to macOS Sequoia, you’re likely dealing with a permissions, connection, or formatting issue—not a dead drive. Start by reconnecting the drive, checking System Settings > General > Storage, and opening Disk Utility to see if it appears there; if it does, a quick First Aid run often fixes it. Below are the detailed steps, likely causes, and answers to common questions.
Why Sequoia Specifically Causes Mounting Problems
macOS Sequoia introduced stricter security and privacy controls, particularly around external storage access. When you connect a drive for the first time, macOS may prompt you to allow the accessory to connect—if you miss or dismiss this prompt, the drive won’t mount. Additionally, Sequoia requires explicit permission for apps to access external volumes; if a background app or Finder itself is blocked, the drive may not appear. This is not a hardware failure in most cases, but a software gatekeeping issue.
Step-by-Step Fixes to Try (In Order)
- Reconnect and check physical connections. Unplug the drive, wait 10 seconds, and plug it back into a different port—preferably directly into the Mac (avoid hubs). Try a different cable if you have one; USB-C and Thunderbolt cables are common failure points.
- Check System Settings > General > Storage. If the drive appears here with a capacity, macOS sees it; the issue is mounting. Click the “i” icon next to it and try “Mount.”
- Open Disk Utility. Go to Applications > Utilities > Disk Utility. If the drive appears in the sidebar (even greyed out), select it and click “First Aid.” This checks and repairs the volume directory—many mounting issues are caused by minor directory corruption.
- Restart your Mac. A simple restart often clears temporary permission glitches introduced during the Sequoia update.
- Reset the NVRAM (Apple Silicon: just restart; Intel: restart and hold Option+Command+P+R). On Intel Macs, this clears certain hardware settings that can affect drive recognition.
- Boot into Safe Mode. Restart and hold the Shift key. In Safe Mode, macOS disables some extensions and clears caches. If the drive mounts there, a third-party extension is likely blocking it in normal mode.
If the Drive Still Doesn’t Appear: Check Formatting and Partition Map
Sequoia (like all recent macOS versions) natively reads APFS, HFS+, and FAT32/exFAT. If your drive is formatted as NTFS (Windows default), macOS can read it but not mount it automatically without third-party software. To check the format, open Disk Utility and look at the drive’s top-level entry (the physical disk, not the volume below it). If it says “Windows NTFS,” you have three options:
- Use a third-party NTFS driver (like Paragon or Tuxera) to mount it read-write.
- Reformat the drive to exFAT if you need cross-platform compatibility (this erases all data).
- Use Terminal to force-mount it read-only:
sudo mount -t ntfs -o ro /dev/disk2s1 /Volumes/mountpoint(replace disk identifier and mountpoint).
Also verify the partition map scheme: for Intel Macs, GUID Partition Map is required to boot, but for external storage, Master Boot Record (MBR) works fine for data. If the drive uses Apple Partition Map (older), Sequoia may refuse to mount it—you’d need to reformat.
Common Misconception: “The Drive Is Dead”
Most users jump to hardware failure, but drives that don’t mount often have recoverable logical issues. Before assuming the worst, check if the drive spins up (listen for a hum) or shows a light. If it does, the problem is almost certainly software. If it’s completely silent and no LED, try a powered hub or a different power source—some portable drives need more power than a single USB port provides. If it still doesn’t respond on another computer, then it’s likely physical.
When to Use Terminal Commands (Advanced)
If Disk Utility won’t mount the drive, you can try forcing it via Terminal. Open Terminal and type diskutil list to find the drive’s identifier (e.g., /dev/disk2). Then run diskutil mountDisk /dev/disk2. If that fails, try diskutil repairDisk /dev/disk2 (this may take a while). These commands often succeed where the GUI fails because they bypass some permission checks. Be careful: only repair the external drive, never your internal disk (usually disk0).
Preventing Future Mounting Issues in Sequoia
- When connecting a new drive, always click “Allow” on the accessory permission prompt.
- In System Settings > Privacy & Security > Files and Folders, ensure Finder and your file manager apps have access to “Removable Volumes.”
- Eject drives properly before unplugging to avoid directory corruption.
- Keep macOS updated—Apple has released patches for external drive bugs in point releases.
Frequently Asked Questions
Why does my drive mount on another Mac but not on Sequoia?
This points to a Sequoia-specific permission or extension conflict. Try the steps above, especially Safe Mode and resetting NVRAM. If it works on another Mac, the drive itself is fine.
Can I recover data from a drive that won’t mount?
Yes, usually. First, try Disk Utility First Aid. If that fails, use a data recovery tool like Disk Drill or PhotoRec (free) to scan the raw disk. Do not reformat before attempting recovery.
Does Sequoia support NTFS drives?
Sequoia can read NTFS but not write to it by default, and some users report it doesn’t mount automatically. Use a third-party NTFS driver or reformat to exFAT for full compatibility.
Why does my drive mount but not show on the desktop?
Go to Finder > Settings > General and check “External disks” under “Show these items on the desktop.” If it’s already checked, the drive might be mounted but hidden; use Disk Utility to see it.
Is it safe to use Terminal to force-mount?
Yes, if you use the correct disk identifier. Double-check with diskutil list before running any command. Never run repair on your internal disk unless you know what you’re doing.
Related
Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.