HTD 8T 5mm Pitch Calculator: Teeth, Diameter, Center Distance
The calculator for this page is switched off while it is checked. The formula is below, and the worked example in the article shows how to use it by hand.
This calculator works out the key dimensions of an HTD (High Torque Drive) timing belt drive with a 5mm pitch (HTD 8M profile, 8mm pitch is different; 5mm pitch is the HTD 5M profile). You enter the number of teeth on the small pulley (driver), the number of teeth on the large pulley (driven), and the center distance between the two pulley shafts; the calculator returns the pitch diameters of both pulleys, the belt length in teeth and millimeters, and the exact center distance for that belt length. It uses the standard HTD 5M geometry with a 40° tooth profile and a pitch line offset of 0.686 mm.
Formula
HTD 5M pulleys have a pitch circle diameter directly proportional to the number of teeth. The pitch (distance between tooth centers measured on the pitch line) is 5 mm, so:
Pulley pitch diameter d = (number of teeth × pitch) / π
where d is in millimeters, teeth count is an integer, and pitch = 5 mm. For a 20-tooth pulley, d = 20 × 5 / π = 31.83 mm. The same formula applies to both pulleys.
The belt length for two pulleys of different diameters at a given center distance comes from the standard open-belt length equation:
L = 2C + π(d1 + d2)/2 + (d2 − d1)² / (4C)
where L is the theoretical belt pitch length (mm), C is the center distance (mm), d1 is the small pulley pitch diameter, and d2 is the large pulley pitch diameter. Because belts only come in whole numbers of teeth, you round L up or down to the nearest multiple of 5 mm (one tooth), then recalculate the actual center distance from that chosen belt length using the quadratic form:
C = [L − π(d1 + d2)/2 + √((L − π(d1 + d2)/2)² − 2(d2 − d1)²)] / 4
All lengths are in millimeters. The square root term must be real; if it is negative, the belt is too short to wrap both pulleys.
Worked Example
Using the default values: small pulley 20 teeth, large pulley 40 teeth, desired center distance 150 mm.
Step 1 – Pitch diameters:
d1 = 20 × 5 / π = 31.83 mm
d2 = 40 × 5 / π = 63.66 mm
Step 2 – Theoretical belt length:
L = 2×150 + π(31.83 + 63.66)/2 + (63.66 − 31.83)² / (4×150)
L = 300 + 150.00 + 1.69 = 451.69 mm
Step 3 – Round to nearest whole tooth (5 mm):
451.69 / 5 = 90.34 teeth → round to 90 teeth → belt length = 450 mm.
Step 4 – Actual center distance with a 450 mm belt:
C = [450 − π(31.83 + 63.66)/2 + √((450 − 150.00)² − 2(31.83)²)] / 4
C = [450 − 150.00 + √(90000 − 2026)] / 4 = [300 + 296.62] / 4 = 149.15 mm
So with a 90-tooth belt (450 mm), the center distance becomes 149.15 mm instead of the requested 150 mm. That is the number you would use for your frame or motor mount.
How HTD 5M Differs from Other Pitches
HTD stands for High Torque Drive, a trapezoidal-curvilinear tooth profile developed to handle higher torque than standard trapezoidal belts. The 5M designation means 5 mm pitch. Common HTD pitches are 3M (3 mm), 5M (5 mm), and 8M (8 mm). The 5M is a middle ground: finer than 8M for compact drives, but coarser than 3M for higher torque capacity. A 5M belt with 15 mm width is typical for 3D printers and small CNC machines; 20 mm width is used for heavier loads. The tooth profile has a 40° included angle and a specified root radius; the pitch line lies 0.686 mm above the tooth root, which is why the pulley outside diameter is slightly less than the pitch diameter.
Do not confuse HTD 5M with GT2 (2 mm pitch) or GT3 (3 mm pitch) belts. GT profiles have a different tooth shape and are not interchangeable with HTD even if the pitch matches. Always match belt profile and pitch to the pulley grooves.
How to Choose the Number of Teeth
Minimum pulley tooth count matters. For HTD 5M, a 10-tooth pulley is the practical minimum; fewer teeth cause excessive tooth bending and premature wear. For smooth motion at moderate speeds, 14–20 teeth is common. Larger pulleys reduce belt flexing and noise but increase inertia.
When selecting teeth, consider the speed ratio you need. If the motor runs at 3000 rpm and you want 1500 rpm output, use a 2:1 ratio – for example, 20 teeth on the motor and 40 teeth on the driven pulley. The pitch diameters scale directly with tooth count, so the ratio is simply z2 / z1.
Center distance should be at least the diameter of the large pulley plus a little clearance, and no more than about 8 times the small pulley diameter to avoid belt whip. The calculator assumes you have a target center distance in mind; if you have a fixed belt length instead, enter trial center distances until the belt length matches the belt you have.
Common Mistakes and Misconceptions
- Using outside diameter instead of pitch diameter. The pitch diameter is larger than the pulley outside diameter. The difference is about 1.37 mm for HTD 5M (twice the pitch line offset). Using the outside diameter in the belt length formula gives a belt that is too short.
- Mixing units. The formula works only if all lengths are in millimeters. If you measure center distance in inches, convert to mm first (1 inch = 25.4 mm).
- Forgetting to round the belt length. Belts come in whole tooth counts. A theoretical length of 451.69 mm does not exist; you must round to 450 mm or 455 mm.
- Assuming the rounded belt gives the exact center distance you wanted. It does not. The actual center distance changes by roughly half the difference between the rounded and theoretical belt length. The calculator gives you that corrected value.
- Using the formula for crossed belts. The equation above is for an open (parallel) belt drive. If your belt wraps around an idler or crosses itself, the geometry changes.
Reading the Results and Adjusting for Tension
The center distance from the calculator is the theoretical pitch-line distance. In practice, you need a small amount of belt tension, which lengthens the belt slightly and increases the center distance. A common rule is to add 0.5–1% of the belt length as installation allowance. For a 450 mm belt, that is 2.25–4.5 mm. Most designs use a slotted motor mount or an idler pulley to adjust tension after installation.
If the calculated center distance is less than the large pulley radius plus the small pulley radius, the pulleys would overlap. That configuration is physically impossible. Increase the center distance or reduce the large pulley teeth.
Frequently Asked Questions
What is the difference between HTD 5M and HTD 8M?
HTD 5M has a 5 mm pitch; HTD 8M has an 8 mm pitch. The 8M is larger and carries more torque, but requires bigger pulleys for the same tooth count. A 20-tooth pulley is 31.8 mm in diameter for 5M but 50.9 mm for 8M. They are not interchangeable.
Can I use a GT2 belt on an HTD 5M pulley?
No. GT2 has a 2 mm pitch and a different tooth profile. Even if the pitch matched, the tooth shape and root radius differ, causing slippage and rapid wear. Always match belt and pulley profile exactly.
How do I know the belt width I need?
Width is separate from pitch. For HTD 5M, common widths are 6, 9, 12, 15, and 20 mm. Wider belts carry more load. For a light 3D printer axis, 6–9 mm is often enough; for a CNC spindle drive, 15–20 mm is typical. The torque rating depends on width, belt material (rubber vs. polyurethane), and speed.
What happens if I use a belt with one more tooth than calculated?
The center distance increases by roughly 2.5 mm (half the pitch) for a 5M belt, plus a small correction for the diameter difference. The drive still works, but you may need more tensioner travel. One tooth more is usually acceptable; two teeth more may make the belt too loose to tension properly.
Is the pitch diameter the same as the pulley outside diameter?
No. The pitch diameter is larger. For HTD 5M, the outside diameter is approximately the pitch diameter minus 1.37 mm. The teeth of the belt sit slightly below the pitch line, so the pulley grooves are shallower than the tooth height.
Can I use this calculator for a belt with an idler pulley?
No. An idler changes the wrap angle and belt path, so the simple two-pulley formula does not apply. You would need to account for the idler position and its effect on the belt length, which requires a more complex geometric calculation.
Related
Formula used
in z1 | Small pulley teeth | teeth | 20 | 10 in z2 | Large pulley teeth | teeth | 40 | 10 in cd | Desired center distance | mm | 150 | 0 out d1 | Small pulley pitch dia | mm | z1 * 5 / pi | 2 out d2 | Large pulley pitch dia | mm | z2 * 5 / pi | 2 out bl_teeth | Belt length (nearest tooth) | teeth | round(2 * cd / 5 + (z1 + z2) / 2 + ((z2 - z1) / (2 * pi))^2 * 5 / cd, 0) | 0 out bl_mm | Belt length | mm | bl_teeth * 5 | 1 out cd_real | Center distance for chosen belt | mm | (5 * bl_teeth - pi * (d1 + d2) + sqrt((5 * bl_teeth - pi * (d1 + d2))^2 - 2 * ((z2 - z1) * 5 / pi)^2)) / 4 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.