ThisCalculator

Everyday

Master Dial Lock Unlock: Step-by-Step Guide

Updated · Standard formula, shown below

This guide explains how to open a Master Lock combination dial lock when you know the combination but are having trouble, or when you need to reset it to a new combination. You will learn the correct dialing technique, how to set a new combination, and what to do if the lock does not open. No special tools are needed, just the lock itself and a little patience.

What You’ll Need

  • The Master Lock dial lock (e.g., model 1500, 175, or similar)
  • The current combination (if you are resetting) or the factory-set combination (if it is new)
  • A pen or pencil to note the new combination (optional but recommended)

Step-by-Step

Opening the Lock with the Combination

  1. Check the shackle position: Ensure the shackle (the U-shaped metal loop) is fully pushed down into the lock body. If it is not, press it in firmly.
  2. Start at zero: Rotate the dial clockwise (right) at least three full turns, and then stop on the first number of your combination. This clears any previous partial rotations.
  3. Turn counterclockwise (left): Rotate the dial counterclockwise one full turn, passing the first number once, and then stop on the second number of your combination on the second time you land on it. (You will pass the number once, then stop on it the next time it comes around.)
  4. Turn clockwise again: Rotate the dial clockwise directly to the third number of your combination. Do not pass it; stop exactly on it.
  5. Pull the shackle: While holding the dial in place, pull up on the shackle. The lock should open. If it does not, repeat the process, ensuring you are accurate with each stop.

Resetting to a New Combination (For Locks with a Reset Lever)

  1. Open the lock: Use the current combination to open the lock as described above.
  2. Rotate the shackle: While the lock is open, rotate the shackle 90 degrees (a quarter turn) and press it down firmly. Keep it pressed down.
  3. Set the new combination: While holding the shackle down, turn the dial to your desired new combination. Make sure each number is aligned exactly with the indicator mark.
  4. Release the shackle: Lift the shackle back up and let it return to its normal position. Your new combination is now set.
  5. Test the new combination: Close the lock and try opening it with the new combination to ensure it works.

Common Mistakes

  • Not clearing the dial: Failing to rotate the dial several times before starting can leave the lock in an intermediate state, causing the combination to fail.
  • Incorrect direction: Mixing up the clockwise and counterclockwise rotations, especially on the second number, is the most frequent error.
  • Stopping on the wrong number: For the second number, it is easy to stop on the first pass instead of the second. Always count the passes.
  • Not pressing the shackle down fully during reset: If the shackle is not fully depressed, the reset mechanism will not engage, and the combination will not change.
  • Using a combination that is too close to the previous one: Some locks have a “false gate” mechanism that can cause issues if the new combination is within a few numbers of the old one. Try to choose numbers that are at least 5 digits apart.

Tips

  • Use a consistent reference point: Always align the numbers with the small arrow or mark on the lock body, not the center of the dial.
  • Dial slowly: Rushing can cause you to overshoot the numbers. If you overshoot, you must restart the entire sequence.
  • Practice with the lock open: Before closing it, practice the dialing sequence a few times so you are confident in the motions.
  • Write down your new combination: Keep it in a safe place, but not attached to the lock itself.
  • Lubricate if stiff: If the dial is hard to turn, apply a small amount of graphite powder (not oil) to the dial spindle.

Troubleshooting

  • The lock does not open after following the steps: Double-check that you are using the correct combination. If you recently reset it, try the old combination in case the reset did not take. Also, ensure the shackle is fully pushed down before starting.
  • The dial will not turn smoothly: This could be due to dirt or debris. Try blowing compressed air into the dial area or using a graphite lubricant. If the dial is still stuck, the lock may be damaged.
  • You forgot the combination: Unfortunately, there is no way to retrieve a forgotten combination without the serial number. If you have the serial number, you can contact Master Lock’s customer service for a combination lookup (they may require proof of ownership). Otherwise, the lock will need to be cut.
  • The reset lever does not move: Some models have a small reset button instead of a shackle rotation. Check your lock’s manual. If it is a shackle rotation type, make sure you are rotating it a full 90 degrees and pressing down firmly.
  • The lock opens with the wrong combination: This is extremely rare and indicates a mechanical failure. The lock should be replaced.

Frequently Asked Questions

What if my lock has a keyhole instead of a reset lever?

Some Master Lock models have a key override. To reset, you would need the key. Insert the key and turn it to the reset position, then set the new combination while the key is turned.

Can I reset the lock without the current combination?

No, you must be able to open the lock to access the reset mechanism. If you do not know the combination, you cannot reset it without cutting the lock or contacting the manufacturer.

How many times do I need to rotate the dial for the first number?

You need to rotate the dial clockwise at least three full times to clear the mechanism, then stop on the first number. Some locks may require more, but three is standard.

Why does my lock sometimes open on the second try?

This often happens when you are not stopping exactly on the numbers. A slight overshoot or undershoot can cause the internal gates to not align perfectly. Make sure you are looking straight at the dial and aligning the numbers precisely.

Is there a way to open the lock if I know the combination but it is stuck?

Try applying gentle pressure to the shackle while turning the dial. Sometimes a slight tug helps the internal mechanism engage. If that does not work, try tapping the lock body lightly with a rubber mallet while dialing. If it still does not open, the lock may be jammed and need replacement.

Can I use the same combination for multiple locks?

Yes, you can set the same combination on multiple locks if they are all resettable. Just make sure you set each one individually.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.