ThisCalculator

Everyday

How to Fit a Samsung Frame TV (Step-by-Step)

Updated · Standard formula, shown below

This guide walks you through fitting a Samsung Frame TV, covering wall mounting, the One Connect box, and the slim-fit wall mount. You’ll learn the exact steps, tools, and common pitfalls so your TV sits flush and looks like a piece of art.

What You’ll Need

  • Samsung Frame TV (with included slim-fit wall mount and One Connect box)
  • Stud finder
  • Pencil
  • Spirit level
  • Drill with appropriate masonry or wood bit
  • Screwdriver (usually Phillips)
  • Socket wrench or spanner (for bolts on the TV back)
  • Measuring tape
  • Wall anchors (if not mounting directly into studs)
  • Optional: cable cover or conduit for the One Connect cable

Step-by-Step

  1. Unpack and lay the TV face-down on a clean, soft surface like a blanket on the floor. Remove the stand if pre-attached. Keep the box and foam for later.
  2. Attach the slim-fit wall mount brackets to the back of the TV. The Frame TV comes with two metal brackets that slide into the recessed slots on the back. Align them and secure with the provided screws (usually four per bracket). Tighten firmly but don’t over-torque.
  3. Locate the studs in your wall using a stud finder. Mark the center of each stud with a pencil. The Frame TV’s wall mount requires two studs (16 or 24 inches apart) for a secure fit. If your studs are not at the right spacing, you may need a different mount or a plywood backing plate.
  4. Measure and mark the mount’s position. Hold the wall plate (the part that attaches to the wall) against the wall at your desired height. Use a spirit level to ensure it’s perfectly horizontal. Mark the screw holes through the plate onto the wall. The typical height is eye-level when seated, about 42-48 inches from floor to the center of the screen.
  5. Drill pilot holes at the marked positions. Use a drill bit slightly smaller than your screws. For drywall over studs, drill into the stud. For plaster or masonry, use appropriate anchors and bits.
  6. Secure the wall plate to the wall using the provided lag bolts or screws. Tighten them with a socket wrench or screwdriver. Ensure the plate is level and firmly attached. Give it a gentle tug to confirm it’s solid.
  7. Connect the One Connect cable to the TV (the thin, near-invisible cable) and to the One Connect box. This box is the brain of the TV – it holds the HDMI ports and power connection. You’ll need to route this cable from the TV to wherever you place the box (often in a cabinet or behind the TV). If you’re hiding it in the wall, use an in-wall rated cable conduit to meet safety codes.
  8. Hang the TV on the wall plate. With two people, lift the TV and align the brackets on the back with the hooks on the wall plate. Gently lower the TV onto the plate. You should hear a click or feel it lock into place.
  9. Secure the anti-tip safety latch (if included). The Frame TV’s mount has a small locking screw at the bottom of the wall plate that you can tighten to prevent accidental lift-off. Use a screwdriver to tighten it.
  10. Connect the One Connect box to power and your other devices (cable box, game console, etc.). Plug the box into a wall outlet. Turn on the TV and verify the picture is working.
  11. Adjust the TV’s tilt and level. The Frame TV mount allows a small tilt adjustment. Use the level on the TV’s top edge and adjust the screws on the mount if needed. Then tighten all adjustment screws.
  12. Hide the One Connect cable. Use the included cable clips to run the thin cable along the back of the TV and down the wall. For a clean look, you can use a cable cover that matches your wall color.
  13. Set up the Art Mode. Turn on the TV, go to Settings > Art Mode, and choose a piece of artwork or your own photos. The TV will display it when in standby, making it look like a framed picture.

Common Mistakes

  • Not using studs: The Frame TV is heavy; mounting into drywall alone will fail. Always anchor into at least two studs.
  • Incorrect bracket orientation: The brackets on the TV back have arrows or labels. Installing them upside down will prevent the TV from hanging correctly.
  • Forgetting to route the One Connect cable before hanging: Once the TV is on the wall, it’s very hard to thread the cable through the wall or behind the TV. Plan the cable path first.
  • Over-tightening screws: This can strip threads or crack the TV’s plastic back. Tighten until snug, then stop.
  • Ignoring the tilt adjustment: If the TV isn’t level, you may need to adjust the small screws on the wall plate’s bottom edge. Don’t force it – consult the manual.

Tips

  • Use a second person to help lift and hang the TV. It’s large and fragile.
  • Keep the box and foam until you’re sure everything works – you’ll need them if you ever move or return the TV.
  • Measure twice, drill once – verify the height and level before drilling.
  • For a truly flush look, use the optional No-Gap wall mount (sold separately) which brings the TV even closer to the wall, but the included slim-fit mount is already very close.
  • If you’re hiding the One Connect cable in the wall, use a low-voltage rated cable or conduit. Check local building codes.

Troubleshooting

  • TV won’t hang on the plate: Check that the brackets are aligned with the hooks. Sometimes the anti-tip screw is in the way. Loosen it slightly, hang the TV, then re-tighten.
  • TV is crooked: Use the level to check the wall plate itself. If the plate is level but the TV isn’t, adjust the tilt screws on the bottom of the plate. If it’s still off, the wall may be uneven – use shims behind the plate.
  • One Connect cable not working: Ensure the cable is fully seated at both ends. Try a different HDMI port on the One Connect box. If the TV shows no signal, the cable might be damaged – replace it with a new one from Samsung.
  • TV falls forward slightly: The anti-tip latch may not be engaged. Push the TV firmly against the wall and tighten the locking screw at the bottom of the mount.
  • Art Mode not appearing: Make sure the TV is in standby (not off) and that Art Mode is enabled in settings. If you don’t see your own photos, check the Samsung SmartThings app for photo upload.

Frequently Asked Questions

  1. Can I use a regular wall mount with the Frame TV? Yes, but the slim-fit mount is designed to make the TV sit flush. A standard mount may leave a gap. If you use a third-party mount, ensure it’s VESA compatible and rated for the TV’s weight.
  2. How far from the wall does the Frame TV sit with the included mount? With the slim-fit mount, the TV sits about 0.2 inches (5 mm) from the wall, which is nearly flush. The optional No-Gap mount brings it to about 0.1 inches (2.5 mm).
  3. Do I need to hide the One Connect box? No, you can place it on a shelf or cabinet. But the thin cable is designed to be hidden. The box itself is small and can be tucked away.
  4. Can I mount the Frame TV on plaster or brick? Yes, but you’ll need appropriate anchors or masonry screws. The included screws are for wood studs. For brick, use sleeve anchors.
  5. What if my studs are not at the right spacing? The included mount requires studs at standard 16 or 24 inches. If yours are different, you can install a plywood board across the studs and mount to that, or use a different wall mount with adjustable brackets.
  6. How do I remove the TV from the wall later? Tilt the TV forward slightly, then lift it up and off the hooks. Disconnect the One Connect cable first. Keep the screws and brackets in a safe place.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.