ThisCalculator

Everyday

FPGA Console Setup for PAL and NTSC Displays

Updated · Standard formula, shown below

This guide walks you through configuring an FPGA-based retro console (like a MiSTer or a custom FPGA board) to output video correctly on both PAL and NTSC displays. You’ll learn how to set the video mode, adjust timing, and handle common issues like rolling images or black-and-white output. Before starting, ensure your FPGA core or firmware supports multiple video standards and that you have a compatible display or upscaler.

What You’ll Need

  • FPGA development board or FPGA-based console (e.g., MiSTer, DE10-Nano, or similar)
  • Display that accepts PAL or NTSC signals (CRT TV, LCD with composite/component input, or a good upscaler)
  • Cables: composite, component, or HDMI depending on your setup
  • SD card with the latest FPGA core/firmware (e.g., MiSTer SD card image)
  • Keyboard or controller for navigating the OSD (on-screen display)
  • Optional: USB hub and power supply for the FPGA board

Step-by-Step

  1. Identify your display’s native standard. Check the back of your TV or monitor for “PAL” or “NTSC” labels. Most modern displays handle both, but older CRTs are region-locked. If you’re using an upscaler, know its input capabilities.
  2. Update your FPGA firmware and cores. Download the latest version of your FPGA framework (e.g., MiSTer) and the specific console cores you plan to use. Copy them to the SD card following the official installation guide for your board.
  3. Power on the FPGA and connect to a display. Initially, connect via HDMI if possible, as it’s more forgiving. If you’re using analog output (composite/component), connect the appropriate cable to the display.
  4. Access the OSD (On-Screen Display). Press the OSD button on your controller or keyboard (typically F12 for MiSTer). Navigate to the “Video” or “Display” settings menu.
  5. Set the video standard. Look for an option like “Video Standard,” “TV Standard,” or “VSync Adjust.” Choose either “PAL” or “NTSC” to match your display’s native format. If your display is multi-standard, pick the one that matches the core’s region (e.g., PAL for European games).
  6. Adjust the video mode. Some cores allow you to set the resolution and refresh rate manually. For PAL, the standard is 720×576 at 50Hz; for NTSC, it’s 720×480 at 60Hz. Select the appropriate mode if available. On MiSTer, you can enable “Direct Video” for analog output or use “HDMI” for digital.
  7. Set the aspect ratio. Choose “4:3” for classic consoles, unless you’re using a widescreen hack. This ensures the image isn’t stretched.
  8. Test with a known game. Load a game that uses the correct region (e.g., a PAL game for PAL). Check for color correctness, stable picture, and proper audio sync.
  9. Fine-tune the sync. If the image rolls or is offset, adjust the “VSync” or “HSync” settings. On MiSTer, you can enable “Sync on Green” for component or adjust the “VGA Scaler” settings.
  10. Save your settings. Once everything looks good, navigate to the OSD and choose “Save Settings” or “Save Configuration.” This ensures your changes persist across reboots.

Common Mistakes

  • Mismatched region and core. Running a PAL game on an NTSC core (or vice versa) often results in a black-and-white image or a rolling picture. Always match the core’s region to the game’s region.
  • Using the wrong cable. Some FPGA boards output RGB via a VGA connector, not composite. If you connect a composite cable to a VGA port, you’ll get no signal. Use the correct adapter or cable type.
  • Ignoring the display’s native resolution. Forcing a PAL signal on an NTSC-only display (or a modern monitor without 50Hz support) will cause flicker or no image. Always check your display’s supported refresh rates.
  • Forgetting to save settings. Many users adjust settings, then reboot, and lose everything. Always save your configuration after making changes.

Tips

  • If you’re using a modern LCD, consider enabling the “VGA Scaler” or “HDMI Scaler” on MiSTer. This converts the low-res retro signal to a higher resolution, improving compatibility and image quality.
  • For CRT displays, use a high-quality composite or component cable. Cheap cables can introduce noise and color bleeding.
  • When in doubt, start with the default video settings for your core, then make one change at a time. This makes it easier to identify what fixes the issue.
  • If your display supports both PAL and NTSC, test both and choose the one that gives the most stable picture. Some displays handle one better than the other.

Troubleshooting

  • No picture at all. Check that the cable is firmly connected and the display is set to the correct input. If using HDMI, try a different HDMI port. If using analog, ensure the display is set to “Composite” or “Component” accordingly.
  • Black-and-white image. This usually means a PAL/NTSC mismatch. Change the video standard in the OSD to match your display’s native standard. If that doesn’t work, try a different cable (some cables don’t carry color correctly).
  • Rolling or tearing image. This is a sync issue. Adjust the VSync/HSync settings or enable “Sync on Green” if using component. On MiSTer, you can also try toggling “VSync Adjust” to “PAL60” or “NTSC50” for mixed content.
  • Image is too dark or too bright. Adjust the brightness/contrast on your display, or check the core’s video settings for a “Gamma” or “Brightness” option.
  • Sound is out of sync. This can happen if the video refresh rate is wrong. Ensure the core is set to the correct refresh rate (50Hz for PAL, 60Hz for NTSC). If using a scaler, check if it introduces latency.

Frequently Asked Questions

Can I use the same FPGA setup for both PAL and NTSC displays?

Yes, most FPGA consoles allow you to switch between PAL and NTSC modes via the OSD. You’ll need to change the setting each time you switch displays, or use a display that supports both standards.

Why does my PAL game show in black and white on my NTSC TV?

Because the TV is trying to decode the PAL color signal as NTSC. Change the FPGA’s video standard to NTSC (or use a multi-standard TV) to get color.

What is the difference between PAL and NTSC in terms of resolution?

PAL uses 576 visible lines at 50Hz, while NTSC uses 480 lines at 60Hz. Both are 4:3 aspect ratio. The higher line count of PAL gives slightly more vertical resolution, but the lower refresh rate can cause flicker.

Do I need a special cable for PAL vs NTSC?

No, the cable type (composite, component, HDMI) is the same. The difference is in the signal timing, which is set by the FPGA, not the cable.

Can I force a PAL game to run in NTSC mode?

Some cores allow “PAL60” or “NTSC50” modes, which mix the frame rate and resolution. This can make PAL games run at 60Hz on NTSC displays, but the speed may be slightly off.

Why does my modern monitor not display the FPGA’s output?

Many modern monitors don’t support 50Hz or low resolutions. Use an upscaler or enable the scaler feature in your FPGA framework to convert the signal to a supported format.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.