ThisCalculator

Everyday

Port Forward Enshrouded Dedicated Server UDP

Updated · Standard formula, shown below

Port forwarding for an Enshrouded dedicated server lets players outside your local network connect to your game. You’ll open specific UDP ports on your router and point them to the computer running the server. Before you start, you need: the server installed and running, a static (or reserved) local IP address for that computer, and access to your router’s admin panel.

What You’ll Need

  • Your router’s admin username and password
  • The local IP address of the computer running the Enshrouded server (e.g., 192.168.1.50)
  • The public IP address of your server (optional, but helpful for testing)
  • Enshrouded dedicated server software (installed via Steam or standalone)

Step-by-Step

  1. Find your server’s local IP address. On the server computer, open Command Prompt (Windows) and type ipconfig. Look for the IPv4 address under your active network adapter (e.g., 192.168.1.50). Write this down.
  2. Set a static IP address (recommended). Without a static IP, your router may assign a new IP later, breaking the port forward. In Windows, go to Control Panel > Network and Sharing Center > Change adapter settings, right-click your adapter, select Properties, then Internet Protocol Version 4 (TCP/IPv4). Choose “Use the following IP address” and enter the IP, subnet mask (usually 255.255.255.0), and default gateway (your router’s IP). Alternatively, set a DHCP reservation in your router’s settings.
  3. Log into your router. Open a web browser and enter your router’s IP address (commonly 192.168.1.1 or 192.168.0.1). Enter the admin credentials. If you don’t know them, check the router label or the manual.
  4. Find the port forwarding section. Look for tabs like Advanced, NAT, Virtual Server, or Port Forwarding. The exact name varies by router brand.
  5. Create a new port forwarding rule. Click “Add” or “Create New”. You’ll need to fill in:
    • Service name: e.g., “Enshrouded”
    • Protocol: UDP (Enshrouded uses UDP only)
    • External port: 15636 (the default game port)
    • Internal port: 15636 (same as external)
    • Internal IP: the server’s static IP (e.g., 192.168.1.50)
  6. Save the rule. Click “Save” or “Apply”. Some routers require a reboot, but most apply immediately.
  7. Test the port forward. From an external network (e.g., a phone on cellular data), try to connect using your public IP address and port 15636. You can also use an online port checker tool, but it must support UDP (many only test TCP). A more reliable test is to have a friend try to join via Steam or the game’s server browser.

Common Mistakes

  • Using TCP instead of UDP. Enshrouded’s dedicated server uses UDP only. If you forward TCP, players won’t connect.
  • Wrong internal IP. Entering the wrong local IP, or an IP that changes later, is the most frequent cause of failure. Always use a static IP.
  • Port mismatch. Ensure the external and internal ports match, and that the game server is actually listening on that port (check the server config file).
  • Forgetting to allow the port in Windows Firewall. Even with port forwarding, the server computer’s firewall must allow inbound UDP on port 15636. Add a rule for both private and public networks.
  • Double NAT. If your ISP modem is also a router, you may have two layers of NAT. You’ll need to forward the port on both devices, or put your router in bridge mode.

Tips

  • Use a DHCP reservation instead of a manual static IP if your router supports it – it’s easier to manage.
  • Check your server’s config file (usually enshrouded_server.json) to confirm the port setting. The default is 15636, but you can change it.
  • Write down your public IP. It changes unless you have a static IP from your ISP. Consider using a dynamic DNS service to get a hostname that always points to your current IP.
  • Test locally first. Connect to your server using its local IP (e.g., 192.168.1.50:15636) to ensure the server works before troubleshooting port forwarding.

Troubleshooting

Players can’t connect after port forwarding.

  • Verify the server is running and listening on the correct port. In the server console, you should see a message like “Server started on port 15636”.
  • Confirm the port forward rule is saved and active. Re-check the internal IP and port.
  • Check the Windows Firewall on the server. Go to Windows Defender Firewall > Advanced Settings > Inbound Rules and create a new rule for UDP port 15636. Allow the connection for all profiles.
  • Test with a tool that supports UDP, like udp-port-checker or a friend’s game client. Many online port checkers only test TCP.
  • If you have a VPN or proxy on the server, disable it temporarily – it can interfere with inbound connections.

Port forward works but players get a timeout.

  • This often indicates a firewall issue on the server or a double NAT. Check if your ISP modem is also routing – try accessing your router’s admin page from the WAN side (e.g., using your public IP) to see if you get a login page. If not, you likely have double NAT.
  • Make sure the server’s local firewall allows inbound UDP, not just TCP.

I changed the port in the config, but it still doesn’t work.

  • Restart the server after changing the config. Also, update the port forward rule to match the new port.

Frequently Asked Questions

Do I need to forward both TCP and UDP?

No. Enshrouded’s dedicated server uses UDP only. Forwarding TCP is unnecessary and won’t help.

What is the default port for Enshrouded dedicated server?

The default UDP port is 15636. You can change it in the server config file, but then you must forward the new port.

Can I use the same port for multiple servers?

No, each server instance needs a unique port. If you run multiple Enshrouded servers, assign different ports (e.g., 15636, 15637) and forward each.

Why does my public IP change?

Most ISPs assign dynamic IPs. To avoid issues, use a dynamic DNS service or purchase a static IP from your ISP.

Do I need to open ports on both my router and my Windows firewall?

Yes. The router forwards external traffic to your server, but the server’s firewall must also allow that traffic to reach the game process.

How can I test if the port is open without a friend?

Use a UDP-specific port checker tool online, or try connecting from a different network (e.g., your phone’s hotspot) using your public IP and port. If the server shows up in the game’s server browser, it’s open.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.