ThisCalculator

Everyday

How to Find Molarity of a Solution

Updated · Standard formula, shown below

The calculator for this page is switched off while it is checked. The formula is below, and the worked example in the article shows how to use it by hand.

This guide shows you how to find the molarity of a solution, which is the number of moles of solute dissolved in one liter of solution. You will learn the formula, work through a step-by-step example, and see how to avoid the most common unit mistakes.

Formula

Molarity (symbol c, sometimes written as M) is defined as the number of moles of solute divided by the volume of the solution in liters:

c = n / V

where:

  • c = molarity, in moles per liter (mol/L), often written as M
  • n = amount of solute, in moles (mol)
  • V = volume of the solution, in liters (L)

If you do not know the moles directly, you can find them from the mass of the solute and its molar mass:

n = m / M

where:

  • m = mass of solute, in grams (g)
  • M = molar mass of solute, in grams per mole (g/mol)

Combining the two gives the full formula used in the calculator:

c = (m / M) / V

Worked Example

Using the default values from the calculator above: you dissolve 58.44 g of sodium chloride (NaCl) in enough water to make exactly 1 L of solution. The molar mass of NaCl is 58.44 g/mol.

Step 1: Find the moles of solute.

n = m / M = 58.44 g / 58.44 g/mol = 1.00 mol

Step 2: Divide by the volume in liters.

c = n / V = 1.00 mol / 1 L = 1.00 mol/L

Result: The solution is 1.00 M (1.00 molar). This matches the calculator output for the default inputs.

When to Use This

Molarity is the standard concentration unit in chemistry labs. You use it whenever you need to:

  • Prepare a solution of a known concentration from a solid solute.
  • Dilute a stock solution to a lower concentration (using the dilution equation M1V1 = M2V2).
  • Convert between mass, moles, and volume in stoichiometry problems.
  • Compare concentrations across different experiments.

Always remember that molarity uses the total final volume of the solution, not the volume of solvent you added. You typically dissolve the solute in a small amount of solvent, then add more solvent until the total volume reaches the mark on the volumetric flask.

Common Mistakes

  • Using solvent volume instead of solution volume: If you add 1 L of water to a solid, the final volume is often slightly more than 1 L. Always measure the final solution volume.
  • Forgetting to convert mL to L: Volume must be in liters. If you have 250 mL, divide by 1000 to get 0.250 L before using the formula.
  • Using the wrong molar mass: For hydrated salts (like CuSO4·5H2O), include the water molecules in the molar mass. For acids like H2SO4, use the full formula mass.
  • Rounding too early: Keep at least three significant figures during intermediate steps, then round at the end.
  • Confusing molality with molarity: Molality (m) is moles of solute per kilogram of solvent, not per liter of solution. They are not interchangeable.

Tips

  • Use a volumetric flask for precise work. A beaker’s markings are not accurate enough for making a standard solution.
  • Check that your solute is dry. Absorbed water adds mass and makes your calculated molarity too high.
  • Write units at every step. If the units do not cancel to give mol/L, you have made an error.
  • For a quick estimate, remember that 1 mole of a typical solid (like NaCl or KCl) weighs roughly 50-100 g, so 58.44 g in 1 L is about 1 M.

Troubleshooting

Your calculated molarity seems too high or too low. Recheck the molar mass. A common error is using the atomic mass instead of the formula mass. For example, NaCl is 22.99 + 35.45 = 58.44 g/mol, not 22.99 g/mol.

The solute will not dissolve completely. Warm the solvent gently (if safe for the solute) and stir. Some solutes, like calcium hydroxide, have limited solubility; if you exceed it, the solution will be saturated and the molarity will not match your calculation.

Your volume reading is off. Read the meniscus at eye level. For a volumetric flask, fill until the bottom of the meniscus touches the calibration line.

The calculator gives an error or a negative number. Check that all inputs are positive. Mass, molar mass, and volume cannot be zero or negative for a real solution.

Frequently Asked Questions

What is the difference between molarity and molality?

Molarity (M) is moles of solute per liter of solution. Molality (m) is moles of solute per kilogram of solvent. Molality does not change with temperature because it depends on mass, not volume.

How do I convert from molarity to grams per liter?

Multiply molarity by the molar mass. For example, a 2.0 M solution of NaCl (58.44 g/mol) contains 2.0 × 58.44 = 116.88 g of NaCl per liter of solution.

What does 1 M mean in plain terms?

1 M means one mole of solute dissolved in enough solvent to make exactly one liter of solution. For NaCl, that is 58.44 g in 1 L total volume.

Can I use this formula for gases dissolved in liquids?

Yes, molarity works for any solute, including gases. You just need the moles of gas (often from the ideal gas law) and the final solution volume.

Does temperature affect molarity?

Yes. Because volume changes with temperature, molarity changes too. If you need a concentration that is temperature-independent, use molality or mole fraction.

How do I prepare a solution of a specific molarity?

Weigh out the required mass of solute (m = M × c × V), dissolve it in a small amount of solvent, then add solvent until the total volume equals V in a volumetric flask.

Related

Formula used
in m | Mass of solute | g | 58.44 | 0
in M | Molar mass of solute | g/mol | 58.44 | 0
in V | Volume of solution | L | 1 | 0
out n | Moles of solute | mol | m / M | 2
out c | Molarity | mol/L | (m / M) / V | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.