ThisCalculator

Everyday

DeWalt FLEXVOLT Batteries: How Voltage Switching Works

Updated · Standard formula, shown below

DeWalt FLEXVOLT batteries change their electrical configuration automatically when you move them between compatible 20V MAX and 60V MAX tools. There is no switch or setting to adjust: the battery’s contacts and the tool’s design determine the voltage configuration. Before connecting one, check that the battery and tool are compatible and that the battery is undamaged.

What You’ll Need

  • A DeWalt FLEXVOLT battery with enough charge for the job.
  • A compatible DeWalt 20V MAX or 60V MAX tool. Check the tool label and its manual; not every DeWalt battery fits every tool.
  • The tool’s manual, if you need to confirm compatibility or the correct way to install the battery.
  • Eye protection and any other protective equipment specified for the tool and task.

Step-by-Step

  1. Identify the tool’s platform. Look for the voltage/platform marking on the tool, battery bay, packaging, or manual. DeWalt commonly labels its cordless platforms 20V MAX and 60V MAX. Do not infer compatibility from a similar-looking battery slot alone.
  2. Confirm that the battery is a FLEXVOLT model. Read the label on the battery. A FLEXVOLT pack is designed to work with compatible 20V MAX tools and to supply the higher-voltage configuration required by compatible 60V MAX tools. A standard 20V MAX battery is not a substitute for a FLEXVOLT pack in a tool that requires FLEXVOLT.
  3. Check the battery and tool. Remove the battery from any charger or tool before inspecting it. Do not use a pack with a cracked case, damaged contacts, signs of leaking, unusual heat, or other visible damage. Check the tool’s manual for approved battery types and any model-specific instructions.
  4. Make the tool safe to handle. Switch the tool off and, where applicable, set its trigger lock. Keep your hands away from moving parts. For equipment with a blade, chain, or other cutting attachment, follow the manual’s instructions for safe handling before fitting the battery.
  5. Align the battery with the tool’s rails. Hold the pack by its case, line up the rails and contacts with the battery bay, and slide it in straight. Do not twist it, force it, or push on the contacts with an object.
  6. Seat the battery until its latch engages. Push the pack in firmly using normal hand pressure. A properly seated battery should be retained by the latch and should not fall out when you release it. If it will not slide in smoothly, stop and check the model compatibility, orientation, and bay for debris.
  7. Let the tool select the compatible configuration. There is no voltage selector to press. In a compatible 20V MAX tool, the FLEXVOLT pack supplies the tool’s 20V MAX-compatible configuration. In a compatible 60V MAX tool, the tool uses the pack’s higher-voltage configuration. The tool and pack are designed to make this change through their contacts when correctly connected.
  8. Check the fit, then start safely. Confirm that the latch holds the pack. Follow the tool manual’s startup instructions, keep the work area clear, and use the tool only for its intended task. If the tool does not run normally, switch it off and remove the battery before investigating.
  9. Remove the pack when finished or before inspection. Switch off the tool, wait for moving parts to stop, press the battery-release button, and slide the pack out. Do not pull it out by the label or pry at the contacts.
  10. Charge and store it appropriately. Use a charger specified for that battery and follow the charging and storage directions in its manual. Keep the battery dry and away from excessive heat, and do not store loose packs where metal objects can bridge the contacts.

Common Mistakes

  • Looking for a manual voltage switch: The pack changes configuration automatically; it does not have a user-operated 20V/60V switch.
  • Assuming every tool is compatible: The FLEXVOLT name does not mean that every DeWalt tool or battery generation fits. Verify the specific tool’s approved battery types.
  • Forcing a pack that does not fit: Misalignment, debris, or an incompatible model can prevent insertion. Forcing it may damage the rails, latch, or electrical contacts.
  • Using “20V” and “60V” as a promise of constant operating voltage: These are platform names. The battery configuration and tool design determine what the compatible tool receives; actual battery voltage can vary with charge and operating conditions.
  • Ignoring warning signs: A hot, damaged, swollen, wet, or unusually smelling battery should not be installed, charged, or opened.
  • Testing with the trigger while fitting the pack: Keep the tool switched off during installation and removal to avoid accidental startup.

Tips

  • Use the markings on the specific tool and battery, rather than relying only on color or appearance.
  • Keep battery contacts clean and dry. If they need cleaning, remove the pack and follow the manufacturer’s care guidance; do not scrape contacts or apply liquid into the tool.
  • For demanding work, let a hot battery cool in a safe, dry place before charging or using it again, following the manual’s temperature guidance.
  • Store batteries securely with their contacts protected from keys, screws, or other conductive items.
  • If you have several packs, note which tool models accept each one. This avoids confusion between FLEXVOLT packs and batteries intended only for a particular platform.

Troubleshooting

The battery will not slide into the tool: Remove it and check that it is the correct compatible model and orientation. Inspect the rails and bay for dirt or damage. Never file, bend, or modify the pack or tool to make it fit.

The battery clicks in but the tool will not start: Switch the tool off, remove and reseat the pack, then check the charge indicator if the model has one. Make sure the tool’s own switch, trigger lock, and any required operating controls are set as described in its manual. Try a known-good, compatible battery if available. If the FLEXVOLT pack works in another compatible tool but not this one, the tool may need service.

The battery appears to work in a 20V MAX tool but not a 60V MAX tool: Confirm that the second tool specifically accepts FLEXVOLT and inspect its battery bay and contacts. A pack that is depleted, too hot, or damaged may also prevent operation. Do not try to change the voltage by covering contacts or altering the pack.

The charger does not charge the battery: Confirm that the charger is listed as compatible in the battery instructions, then reseat the pack and check the charger’s indicator behavior in its manual. Allow an unusually hot or cold pack to reach the recommended charging conditions. Stop if the battery or charger is damaged, smells unusual, or heats excessively.

The pack becomes unusually hot, smells, leaks, or looks swollen: Stop using it. If safe, remove it from the tool and keep it away from flammable materials. Do not open, puncture, or attempt to repair it. Follow local battery-recycling or hazardous-waste guidance, and contact DeWalt support or an authorized service provider for next steps.

Frequently Asked Questions

Do I need to press a button to switch a FLEXVOLT battery from 20V to 60V?
No. The change is automatic when the pack is fitted to a compatible tool; there is no voltage-selection button.

Can a FLEXVOLT battery be used in a 20V MAX tool?
It is designed to work with compatible 20V MAX tools. Check the manual for the exact tool and battery model before use.

Can I use an ordinary 20V MAX battery in a 60V MAX tool?
Do not assume so. A 60V MAX tool may require a compatible FLEXVOLT battery. Follow the tool’s battery requirements.

Does the battery physically change size when it changes voltage?
No. The pack remains the same size; its electrical configuration is selected through the compatible tool’s contacts and design.

Can I use one FLEXVOLT battery in any DeWalt cordless tool?
No. Compatibility depends on the tool and battery model. Check their labels and manuals instead of relying on the brand or appearance alone.

What if the battery fits but the tool does not recognize it?
Remove and reseat it with the tool off, check charge and contacts, and consult the manual. If a compatible pack still fails, stop troubleshooting and contact an authorized service provider.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.