ThisCalculator

Everyday

Custom Guitar Controller Faceplate: Design & 3D Print Guide

Updated · Standard formula, shown below

This guide walks you through creating a custom faceplate for a guitar-shaped game controller, from taking measurements to printing a finished part that fits. You’ll learn the design workflow, common pitfalls, and how to adjust for a snug fit. No prior 3D modeling experience is required, but basic familiarity with your printer’s software helps.

What You’ll Need

  • Digital calipers (essential for accurate measurements)
  • Your guitar controller (e.g., Guitar Hero or Rock Band model)
  • 3D modeling software (free options: Tinkercad, Fusion 360 for personal use, or Blender)
  • Slicer software (Cura, PrusaSlicer, etc.)
  • 3D printer with filament (PLA or PETG recommended)
  • Small screwdriver set (to disassemble the controller if needed)
  • Sandpaper (120, 220, 400 grit) and a hobby knife

Step-by-Step

  1. Disassemble the controller. Remove the screws from the back of the guitar. Carefully separate the two halves. Keep track of which screws go where—they may be different lengths. Set aside the electronics and buttons in a safe place.
  2. Measure the original faceplate. Using calipers, measure the length, width, and thickness of the existing faceplate (the part you’re replacing). Also measure the diameter and position of every screw hole, button opening, and the large strum bar slot. Record all dimensions in millimeters. For curved edges, measure the radius or trace the outline onto paper.
  3. Create a digital sketch. In your 3D modeling software, start a new project. Create a sketch on the top plane. Draw the outer outline of the faceplate using rectangles, arcs, and splines. If your controller has a curved surface, you’ll need to model that curvature later, but start with a flat projection.
  4. Add holes and cutouts. Using the dimensions you recorded, place circles for screw holes and button openings. For the strum bar, create a long slot. Make sure the centers align with your measurements. Use the ‘extrude cut’ or ‘hole’ feature to remove material.
  5. Model the thickness and curvature. Extrude the faceplate to the measured thickness. If the original is curved (most are), use the ‘loft’ or ‘sweep’ tool to create the curve. A simpler approach: model it flat, print it, and then heat-bend it with a hairdryer—but for best results, model the curve directly.
  6. Add alignment tabs. Look at how the original faceplate snaps or screws onto the body. Add small tabs or ridges to your model that match the slots in the controller body. These ensure the faceplate sits flush.
  7. Export as STL. Once the model is complete, export it as an STL file. In most software, this is under File > Export > STL. Choose a high resolution setting.
  8. Slice the model. Open the STL in your slicer. Orient the faceplate so the outer surface faces up (or down, depending on your printer). Add supports if there are overhangs (like the strum bar slot edges). Set layer height to 0.2mm or finer for detail. Use 3-4 perimeters for strength.
  9. Print a test piece. Before printing the full faceplate, print a small section—maybe a corner with a screw hole—to verify the fit. This saves time and filament.
  10. Print the final faceplate. Once the test piece fits, print the full model. Monitor the first few layers to ensure good adhesion.
  11. Post-process. Remove supports carefully. Sand the edges and any rough spots. Test fit on the controller. If it’s too tight, sand the inside edges. If it’s too loose, you may need to reprint with adjustments.
  12. Reassemble the controller. Place the new faceplate onto the body, reinstall the buttons and strum bar, and screw everything back together. Test all buttons and the strum bar for smooth operation.

Common Mistakes

  • Measuring only the outer dimensions. The holes and tabs are just as important—measure them all precisely.
  • Ignoring the curvature. Many controllers have a slight dome. A flat faceplate will wobble or crack.
  • Using too small a hole. 3D printing shrinks holes slightly. Add 0.2-0.4mm tolerance to screw holes and button openings.
  • Printing with too few walls. The faceplate needs to be rigid. Use at least 3 perimeters.
  • Skipping the test print. Always test a small section first—it saves hours of failed prints.

Tips

  • Use PLA for easy printing, but PETG if the controller gets warm or you want more durability.
  • Print with the outer face down on the build plate for a smooth finish—just ensure the build plate is clean and level.
  • Add a small chamfer to the edges of holes to guide buttons in smoothly.
  • If your controller has LED lights, use translucent filament or add a cutout for the light.
  • Keep a digital copy of your measurements—you might want to make a second version later.
  • For a glossy finish, apply a coat of clear spray paint or epoxy resin after sanding.

Troubleshooting

  • The faceplate doesn’t fit at all. Re-measure the original and compare to your model. Check that you didn’t scale the model accidentally (common when importing STL in mm vs inches).
  • Holes are too small. Use a drill or round file to enlarge them slightly. For future prints, add 0.2-0.4mm to the hole diameter.
  • The faceplate is warped. This often happens from printing too fast or with insufficient cooling. Reduce print speed and enable cooling fans. Also, ensure the build plate is heated correctly.
  • Buttons stick. Sand the button holes to smooth them. Also check that the button stems aren’t rubbing against the faceplate—add a small clearance (0.3mm) to the hole.
  • The strum bar doesn’t move freely. The slot might be too tight. Sand the edges or reprint with a slightly wider slot.
  • Layer lines are visible. Use a finer layer height (0.12mm) and sand with progressively finer grits. A coat of primer before painting also hides lines.

Frequently Asked Questions

Do I need to disassemble the whole controller?

Yes, to measure the faceplate accurately and to test fit without the electronics in the way. It also lets you see how the faceplate attaches.

Can I use a 3D scanner instead of calipers?

Yes, a scanner can capture complex curves, but it’s often overkill for a flat-ish faceplate. Calipers are cheaper and more precise for holes and tabs.

What filament should I use?

PLA is easiest to print and works fine for casual use. PETG is more durable and heat-resistant, making it better if you play for long sessions or leave the controller in a hot car.

How do I add a custom design or logo?

In your modeling software, you can emboss or extrude text/shapes onto the faceplate. Alternatively, print a blank faceplate and use vinyl decals or paint.

My controller is a different brand—will this guide still work?

Yes, the process is the same for any guitar controller. Just measure your specific model—the dimensions and attachment points will differ.

Can I sell faceplates I make?

Yes, as long as you designed the model yourself and aren’t using copyrighted logos. Selling 3D printed parts for personal use is generally fine, but check your local laws.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.