ThisCalculator

Everyday

Adjusting Hunger, Thirst & Fatigue on Abiotic Factor

Updated · Standard formula, shown below

Adjusting Hunger, Thirst & Fatigue on Abiotic Factor

This guide shows you how to change the hunger, thirst, and fatigue settings on an Abiotic Factor dedicated server. You’ll edit the server configuration file to make survival mechanics easier or harder, then restart the server to apply the changes. No special tools are needed beyond access to the server’s files.

What You’ll Need

  • Access to the server’s file system (via file manager, FTP, or SSH).
  • The server must be stopped or you must be able to restart it after editing.
  • A text editor (Notepad, VS Code, or similar) to modify the config file.

Step-by-Step

  1. Locate the server config file. On most dedicated servers, this is ServerSettings.cfg or Game.ini inside the server’s Saved/Config/LinuxServer or Saved/Config/WindowsServer folder. If you’re using a hosting panel, look for a “Config Files” or “Server Settings” section.
  2. Open the file in a text editor. Make sure you’re editing the correct file—not the client-side settings.
  3. Find the survival settings section. Look for lines containing HungerRate, ThirstRate, or FatigueRate. These values control how quickly each stat drains. If they don’t exist, you can add them under [/Script/AbioticFactor.SurvivalSettings] or a similar section.
  4. Adjust the values. The default is usually 1.0. Lower values (e.g., 0.5) make the stat drain slower (easier), while higher values (e.g., 2.0) make it drain faster (harder). For example, to reduce hunger drain by half, set HungerRate=0.5.
  5. Save the file. After editing, save the changes and close the editor.
  6. Restart the server. Fully stop and start the server process. A simple reload may not apply config changes.
  7. Verify the changes. Join the server and observe the hunger, thirst, and fatigue bars. If they drain slower or faster as intended, the changes are active.

Common Mistakes

  • Editing the wrong file. Clients have their own settings; make sure you’re editing the server’s config, not the local one.
  • Using incorrect syntax. Values must be numeric, with a period as the decimal separator (e.g., 0.5, not 0,5). Also, ensure the section header is correct.
  • Forgetting to restart. Config changes only take effect after a full server restart.
  • Setting values to zero. A value of 0 may disable the stat entirely, but it can also cause unexpected behavior. Use a very low number like 0.01 if you want almost no drain.

Tips

  • Test with a small change first (e.g., 0.8) to see how it feels before making extreme adjustments.
  • Back up the config file before editing so you can revert if something goes wrong.
  • If you want different difficulty for PvE vs PvP, check if your server supports separate settings per game mode—some do.
  • Combine rate changes with other survival settings (like starting stats) for a balanced experience.

Troubleshooting

Changes don’t take effect. Double-check the file path and ensure you’re editing the correct config. Some hosting panels require you to click “Save” in their interface, not just in the text editor. Also confirm the server fully restarted—not just a map change.

Server won’t start after editing. This usually means a syntax error. Check for typos, missing brackets, or extra spaces. Restore the backup and try again with a single change.

Values reset to default. The server may overwrite the config on startup if the file is in the wrong location or if the game updated. Make sure you’re editing the file that the server actually reads (check logs for the config path).

Only some stats change. Ensure you’ve set all three rates (Hunger, Thirst, Fatigue). They are independent; changing one won’t affect the others.

Frequently Asked Questions

Q: Can I disable hunger, thirst, and fatigue entirely?
A: Yes, set the rates to a very low number like 0.01. While 0 might work, it can cause division-by-zero errors in some game versions.

Q: Do these settings affect all players on the server?
A: Yes, the server config applies to all players equally. There is no per-player setting in the base game.

Q: Will changing these values affect my save file?
A: No, the rates only affect how fast stats drain, not the saved character data. Your current stats will remain as they are.

Q: What if I can’t find the config file?
A: If you’re using a hosting panel, look for a “Config Editor” or “Server Settings” tab. If you have FTP access, search for ServerSettings.cfg in the server root.

Q: Do I need to stop the server before editing?
A: It’s recommended, as the server may overwrite the file on shutdown. Stop the server, edit, then start it again.

Q: Can I use decimal values like 0.75?
A: Yes, any positive number works. Use decimals for finer control.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.