ThisCalculator

Everyday

Adapting Old OM Lenses to OM-D & PEN Cameras

Updated · Standard formula, shown below

Mounting your vintage Olympus OM-system lenses on a modern OM-D or PEN body lets you use classic optics with full manual control, often at a fraction of the cost of new glass. You’ll need a simple adapter (OM to Micro Four Thirds) and a camera that can shoot in manual or aperture-priority mode. This guide covers choosing the right adapter, mounting it safely, and getting sharp, correctly exposed photos.

What You’ll Need

  • An OM-system lens (Olympus OM mount, e.g., 50mm f/1.8, 28mm f/2.8)
  • A Micro Four Thirds camera (OM-D, PEN, or any MFT body)
  • An OM to Micro Four Thirds lens adapter (plain mechanical type, no glass elements)
  • A clean, dry cloth for wiping contacts and lens surfaces
  • Optional: a lens cap and body cap for storage

Step-by-Step

  1. Turn off the camera. This prevents any accidental sensor activation while you’re attaching the adapter.
  2. Remove the camera body cap. Press the lens release button (usually on the front left of the camera) while twisting the cap counterclockwise. Set it aside.
  3. Attach the adapter to the camera. Align the adapter’s mounting index (a small dot or line) with the camera’s lens release button. Insert the adapter and twist clockwise until it clicks into place.
  4. Remove the rear cap from the OM lens. Twist it off counterclockwise. Keep the front cap on for now.
  5. Mount the lens onto the adapter. Align the lens’s aperture ring or its red dot (if present) with the adapter’s matching index. Gently push the lens in and twist it clockwise until it locks with a click.
  6. Set the lens to manual focus. On most OM lenses, slide the focus mode switch (if any) to “M” or simply turn the focus ring. There’s no electronic connection, so the camera won’t know the lens is attached.
  7. Turn on the camera and set it to Manual (M) or Aperture-Priority (A) mode. In A mode, the camera will meter with the lens stopped down to the set aperture. In M mode, you control both shutter speed and aperture.
  8. Enable “Shoot Without Lens” (if needed). In the camera menu, look for “Shoot w/ Lens” or “Release Without Lens” and set it to “On”. This allows the shutter to fire when the camera doesn’t detect a lens. Some cameras do this automatically.
  9. Set the aperture on the lens. Turn the aperture ring to your desired f-stop. Note that the viewfinder may darken as you stop down, since the lens is manual.
  10. Focus manually. Use the focus ring and the camera’s focus peaking (if available) or magnified view to achieve sharp focus. Press the shutter to take the photo.
  11. Review your image. Check the exposure and sharpness. Adjust shutter speed, ISO, or aperture as needed.

Common Mistakes

  • Using an adapter with glass elements. These “correction” adapters degrade image quality. Choose a plain mechanical adapter.
  • Forgetting to set “Shoot Without Lens”. If the camera won’t fire, this is the most likely cause.
  • Mounting the adapter backwards. The adapter has two distinct sides: one for the camera (MFT) and one for the lens (OM). Ensure you attach the correct side to each.
  • Not turning the lens to manual focus. Some OM lenses have a focus mode switch; if left on auto, the focus ring may be stiff or unresponsive.
  • Expecting autofocus. This is a fully manual setup—no electronic communication.

Tips

  • Use focus peaking. In the camera’s menu, enable focus peaking (highlight edges) to make manual focusing easier.
  • Set the lens to its sharpest aperture. Most OM lenses are sharpest around f/5.6 to f/8. Test yours.
  • Use a tripod for critical sharpness. Manual focus and stopped-down metering can lead to camera shake.
  • Keep the lens stopped down for accurate metering in A mode. The camera meters with the aperture you set, but if you change it, the meter updates.
  • Store the adapter and lens with caps on. Dust on the rear element can affect image quality.

Troubleshooting

  • Camera won’t fire. Check that “Shoot Without Lens” is enabled. Also ensure the lens is fully locked onto the adapter and the adapter onto the camera.
  • Image is dark or too bright. In A mode, the camera meters with the lens stopped down. If you’re in M mode, adjust shutter speed or ISO. Also check that the aperture ring is actually changing the blades.
  • Focus ring is very stiff. Some OM lenses have a focus ring that turns only when the lens is set to manual focus. Ensure the switch is on “M”.
  • Adapter is stuck on the camera. Do not force it. Check that you’re pressing the lens release button and twisting in the correct direction (counterclockwise to remove).
  • Lens won’t mount onto adapter. Align the red dots or index marks properly. Some lenses have a small pin that must align with a slot on the adapter.
  • Images are blurry even when focus peaking shows sharp. This can happen if the adapter is too thick or thin, causing the lens to sit at the wrong distance. Try a different adapter brand.

Frequently Asked Questions

Will autofocus work with an OM lens?

No. OM lenses are entirely manual—no autofocus, no aperture control from the camera. You focus and set the aperture manually.

Do I lose image quality with an adapter?

With a plain mechanical adapter, no. It’s just a metal ring with no glass. However, adapters with corrective glass elements can degrade sharpness.

What is the crop factor?

Micro Four Thirds has a 2x crop factor. A 50mm OM lens becomes a 100mm equivalent field of view.

Can I use OM lenses on other mirrorless systems?

Yes, but you’ll need a different adapter (e.g., OM to Sony E, OM to Fuji X). The same principles apply.

Why is my viewfinder dark when I stop down?

Because the lens is stopped down to the set aperture, less light reaches the sensor. This is normal. Use a larger aperture (smaller f-number) for a brighter view.

How do I clean the lens?

Use a blower to remove dust, then a microfiber cloth with lens cleaner. Never use harsh chemicals or paper towels.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.