ThisCalculator

Everyday

Fixed Toshiba No Bootable Device? Step-by-Step Fix

Updated · Standard formula, shown below

If your Toshiba laptop shows “No bootable device” on a black screen, it usually means the BIOS cannot find a drive with a bootable operating system. The fix is often as simple as changing the boot order, reseating the hard drive, or running a startup repair from Windows recovery.

What This Error Means

The “No bootable device” message appears during the Power-On Self-Test (POST), before Windows loads. The BIOS/UEFI firmware checks each storage device (hard drive, SSD, USB, DVD) in a set order and tries to load an operating system from the first one that contains a valid boot sector. If none of the drives have one, you get this error. It is not a Windows problem—it is a hardware or firmware-level problem.

Common triggers include a disconnected or loose hard drive cable, a corrupted boot configuration, a dead CMOS battery resetting the boot order, or a failed drive. On older Toshiba models, the error often appears after a power surge or a forced shutdown.

Step 1: Check the Boot Order in BIOS

The most frequent cause is that the BIOS is trying to boot from a USB drive or network before the internal hard drive. To fix this:

  1. Restart the laptop and press F2 (or F12 for a one-time boot menu) immediately after the Toshiba logo appears.
  2. In the BIOS setup, go to the Boot tab (or Startup on some models).
  3. Use the arrow keys to highlight the internal hard drive (usually labeled with the manufacturer, e.g., “TOSHIBA MK…” or “Samsung SSD”) and press + or – to move it to the top of the list.
  4. Press F10 to save and exit, then choose Yes.

If the hard drive is not listed at all, skip to Step 3.

Step 2: Use the One-Time Boot Menu

If you only need to boot once (e.g., from a recovery USB), press F12 during startup. This brings up a list of detected devices. Select your hard drive or USB. If the drive appears here but not in the BIOS boot order, the issue is just the order. If it does not appear, the drive may not be recognized.

Step 3: Reseat the Hard Drive or SSD

A loose connection is a common cause, especially if the laptop was dropped or recently opened. Reseating the drive is safe if you follow these steps:

  1. Power off the laptop and unplug the AC adapter.
  2. Remove the battery if it is removable (on many Toshiba models, it is internal).
  3. Locate the hard drive bay on the bottom of the laptop. It is usually secured by one or two screws.
  4. Remove the drive, unplug the SATA cable (or slide it out of its connector), then reconnect it firmly.
  5. Reassemble and power on.

If you have an M.2 SSD, it sits flat on the motherboard and is held by a single screw. Remove and reinsert it at a 30-degree angle, then press down and screw it back.

Step 4: Run Windows Startup Repair

If the BIOS sees the drive but Windows still won’t boot, the boot configuration data (BCD) may be corrupted. You can repair it using Windows recovery media:

  1. Create a Windows installation USB on another computer (search “Windows media creation tool” on Microsoft’s site).
  2. Insert the USB into the Toshiba laptop and boot from it (press F12 and select the USB).
  3. Choose your language, then click Repair your computer (bottom-left corner).
  4. Select Troubleshoot → Advanced options → Startup Repair.
  5. Wait for it to finish and restart.

If Startup Repair fails, try Command Prompt from the same menu and run these commands one by one:

bootrec /fixmbr
bootrec /fixboot
bootrec /rebuildbcd

Step 5: Test the Drive with Diagnostic Tools

If the drive still is not detected, it may be failing. Many Toshiba laptops have a built-in diagnostic called PC Diagnostic that you can access by pressing F2 at startup and selecting the “Diagnostics” tab. Run the Quick HDD Test or Full Test. If it reports errors, the drive is likely dead and needs replacement.

You can also remove the drive and connect it to another computer via a USB-to-SATA adapter to see if it appears in Disk Management. If it does not, the drive is physically damaged.

When the Drive Is Dead: Replacement Options

If you need to replace the drive, you have two main choices:

  • 2.5-inch SATA SSD (e.g., 500GB or 1TB) — affordable, fast, and a direct fit for most Toshiba laptops.
  • M.2 SATA SSD — if your model supports it, it is smaller and faster.

After installing the new drive, you will need to reinstall Windows. You can use the same installation USB from Step 4. If you have a product key, it is usually embedded in the BIOS, so Windows will activate automatically once installed.

Frequently Asked Questions

Why does my Toshiba say “No bootable device” after a power outage?

A sudden power loss can corrupt the boot configuration or cause the BIOS to lose its boot order settings. Resetting the boot order in BIOS (Step 1) and running Startup Repair (Step 4) usually fixes it. If the drive itself was damaged by the power surge, you may hear clicking sounds or see the drive not detected.

Can I recover data from a dead hard drive?

If the drive is not detected by the BIOS, data recovery is possible but expensive. Professional services use specialized equipment to read the platters. If the drive is detected but Windows won’t boot, you can often recover files by booting from a Linux live USB (like Ubuntu) and copying files to an external drive.

How do I know if my Toshiba has a 2.5-inch or M.2 drive?

Open the bottom panel and look. A 2.5-inch drive is rectangular and about 2.5 inches wide, connected by a SATA cable. An M.2 drive is a small stick, about the size of a stick of gum, lying flat on the motherboard. You can also check the user manual or search your exact model number online.

Will resetting the BIOS help?

Yes, it can. Resetting the BIOS to factory defaults clears any misconfigured settings. To do this, enter BIOS (F2), find the Exit tab, and choose Load Setup Defaults or Restore Defaults. Save and exit. This will not delete your files.

Why does my Toshiba show this error after I replaced the hard drive?

If the new drive is blank, the BIOS cannot find an OS. You need to install Windows first. Also, ensure the new drive is properly connected and recognized in BIOS. If it is not, check the SATA cable or try a different M.2 slot.

Is there a way to prevent this from happening again?

Keep your BIOS updated (from Toshiba’s support site), use a surge protector, and back up your data regularly. If you are using an older mechanical drive, consider replacing it with an SSD, which is more reliable and faster.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.