Electrolux ZSP2320 Specs, Bags & Filters
The Electrolux ZSP2320 is a compact bagged canister vacuum designed for hard floors and low-pile carpets, with a 700-watt motor, a 1.5-liter dust bag, and a HEPA H13 exhaust filter. This article covers its full specifications, compatible bags and filters, and practical buying and maintenance advice.
Key Specifications at a Glance
The ZSP2320 is part of Electrolux’s UltraSilencer line, known for quiet operation. Here are the main specs you’ll find on the box or in the manual:
- Motor power: 700 watts (input), which is typical for a compact canister in this class.
- Dust bag capacity: 1.5 liters (HEPA filter bag, type E255 or equivalent).
- Filtration: HEPA H13 exhaust filter + microfilter bag, designed to trap 99.95% of particles down to 0.3 microns.
- Noise level: Approximately 68 dB(A) on the highest setting (varies by surface).
- Cord length: 6 meters (20 feet), with a 2-meter hose and 1.5-meter wand.
- Weight: Around 4.5 kg (10 lbs) for the main unit.
- Dimensions: 25 x 28 x 40 cm (W x D x H) – compact enough to store upright.
- Accessories: Combination floor nozzle (hard floor/carpet), crevice tool, dusting brush, and upholstery nozzle (depending on market).
Note that the ZSP2320 is a corded model – it does not have a battery. It uses a standard 220-240V plug in most regions.
Bags and Filters: What You Need to Know
The ZSP2320 uses the Electrolux E255 HEPA bag (also sold as ZSPBAG1 or similar in some regions). These are paper-like bags with a plastic collar that snaps into the bag compartment. You must use genuine or compatible E255 bags – generic bags without the correct collar may not seal properly, reducing suction and letting dust escape.
The exhaust filter is a HEPA H13 filter (part number 4055088194 or equivalent). It should be replaced every 6–12 months depending on use. Some markets also have a pre-motor filter (sponge) that protects the motor – check your manual. The pre-motor filter can be washed and reused, but the HEPA exhaust filter is not washable.
How often to change: Replace the bag when the indicator (if present) shows full, or about every 4–6 weeks for a typical household with pets. If you notice a drop in suction or a musty smell, change the bag sooner.
How the Filtration System Works
Air enters through the floor nozzle, passes through the bag (which traps most dust), then through the motor, and finally exits through the HEPA exhaust filter. The HEPA filter catches microscopic particles that the bag misses, ensuring the air blown back into the room is clean – important for allergy sufferers.
The UltraSilencer name comes from the motor housing design that dampens vibration and noise. The 700W motor is not the most powerful, but it’s sufficient for hard floors and low-pile carpets. For deep-pile carpets or heavy debris, you may need to go over the same spot twice.
Choosing the Right Bags and Filters
When buying replacements, look for:
- Bag type: E255 (also called S-Bag, but that’s a different series – make sure it says E255).
- HEPA filter: H13 grade, not just a foam filter. Check the part number in your manual.
- Brand: Genuine Electrolux parts are recommended for warranty and performance. Third-party bags may fit but could reduce suction or leak dust.
To install the bag, open the front flap, pull the old bag out by its collar (it self-seals), push the new bag’s collar into the slot until it clicks, and close the flap. For the exhaust filter, twist the grille on the side or bottom of the unit (depending on model) and replace the filter.
Common Problems and Troubleshooting
If your ZSP2320 loses suction, check these in order:
- Bag full? Even if the indicator isn’t red, a full bag reduces airflow. Replace it.
- Blockage in hose or wand? Disconnect the hose and look for clogs. Use a broom handle to push out debris.
- Filter clogged? If the exhaust filter is visibly grey or dusty, replace it. A clogged filter restricts airflow just like a full bag.
- Nozzle settings? Make sure the floor nozzle is set for the surface you’re cleaning (hard floor vs carpet).
If the motor runs but there’s no suction, the bag may not be seated correctly. Open the compartment and push the collar in firmly until it clicks.
If the vacuum smells hot or burning, turn it off immediately – the motor may be overheating due to a blocked airflow. Check for clogs and replace the bag/filter.
Comparing the ZSP2320 to Other Canisters
The ZSP2320 sits between the basic ZSP1200 (600W, no HEPA) and the ZSP4300 (800W, larger bag). Compared to a stick vacuum, it offers more suction power and a longer cord, but it’s heavier and requires dragging the canister behind you. It’s quieter than most uprights – the UltraSilencer design makes it a good choice for homes with babies or pets that spook easily.
If you have mostly hard floors, this vacuum is ideal. For wall-to-wall thick carpets, consider a model with a motorized brush head (like the ZSP4300 with a turbo nozzle). The ZSP2320’s suction-only floor nozzle works on low-pile carpets but won’t deep-clean.
Cost and Maintenance
Replacement bags cost roughly $5–10 each (depending on quantity and brand). HEPA filters run $10–15. Over a year, you’ll spend about $50–70 on consumables if you change the bag every 2 months and the filter twice a year. Some users buy generic bags in bulk to save money, but check reviews for fit – a poor seal can ruin the HEPA benefit.
To extend the life of your vacuum:
- Empty the bag before it’s completely full – don’t wait for the indicator.
- Wash the pre-motor filter (if present) every 3 months.
- Clean the floor nozzle bristles of hair and threads.
- Store the vacuum in a dry place, not in a damp garage.
Safety and Usage Tips
Always unplug the vacuum before changing the bag or filter. Do not vacuum wet surfaces or liquids – this is a dry vacuum only. Avoid picking up sharp objects like glass or nails, which can puncture the bag and damage the motor. If you vacuum fine dust (e.g., plaster), the bag will clog faster – use a pre-filter or a shop vac instead.
Keep the cord away from the nozzle – the vacuum can suck in its own cord, causing a tangle. Also, be careful not to run over the cord with the wheels.
Frequently Asked Questions
Can I use any Electrolux bag in the ZSP2320? No, you must use the E255 type bag. Other Electrolux bags (like S-Bag or AeroPro) have different collars and won’t fit.
Where is the HEPA filter located? On the ZSP2320, the HEPA exhaust filter is usually behind a grille on the side or bottom of the unit. Check your manual for the exact location – it’s not inside the bag compartment.
How do I know when to change the bag? Some models have a red indicator on the handle that pops up when airflow drops. If not, listen for a change in motor sound or notice reduced suction.
Is the ZSP2320 good for pet hair? It works on hard floors and low-pile carpets, but the suction-only nozzle may not lift embedded pet hair from upholstery. Use the upholstery tool for furniture.
Can I wash the HEPA filter? No, washing destroys the filter media. Replace it when dirty.
Does the ZSP2320 come with a warranty? Most regions include a 2-year manufacturer warranty, but check your local terms. Keep your receipt.
Related
Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.