First 3D Printer: How to Choose One That Fits
- Filament weight (PLA)
- g
- Result
- Filament cost (PLA)
- USD
- Result
- Print time
- 120 min
- You entered
To choose your first 3D printer, match the machine to the size and material of the objects you actually want to make, then set a realistic budget that includes filament and basic tools. For most beginners, a hobbyist FDM (fused deposition modeling) printer in the $200–$500 range offers the best balance of print quality, community support, and room to learn.
Formula
The calculator estimates the volume of filament your print will use, based on the bounding box of the object (length × width × height). It then converts that volume to weight using the density of PLA (1.24 g/cm³) and estimates cost using a typical price of $30 per kilogram.
Volume (cm³) = (length × width × height) / 1000
Weight (g) = Volume × 1.24
Cost (USD) = Weight × 0.03
Variables: length, width, height in millimeters; volume in cubic centimeters; weight in grams; cost in US dollars.
Worked Example
Using the default values: length = 100 mm, width = 80 mm, height = 50 mm.
- Volume = (100 × 80 × 50) / 1000 = 400,000 / 1000 = 400 cm³
- Weight = 400 × 1.24 = 496 g
- Cost = 496 × 0.03 = $14.88
So a 100×80×50 mm solid PLA object would use about 496 grams of filament and cost roughly $14.88. Note that real prints are not solid; infill percentage (usually 15–30%) reduces material use significantly.
How FDM 3D Printing Works
FDM printers melt a plastic filament (typically 1.75 mm diameter) and deposit it layer by layer on a heated bed. The print head moves in the X and Y axes while the bed (or the head) moves in Z. Each layer is typically 0.1–0.3 mm thick. The most common materials are:
- PLA – easiest to print, low warping, biodegradable, great for models and prototypes.
- PETG – stronger and more heat-resistant than PLA, slightly harder to print.
- ABS – tough and durable, but requires an enclosed printer to prevent warping and fumes.
- TPU – flexible rubber-like material, needs a direct-drive extruder for best results.
Other technologies exist, such as resin (SLA) printers, which use light to cure liquid resin. They produce much finer details but involve messy post-processing and toxic resin handling, making them less ideal for a first printer unless you specifically need high-detail miniatures or jewelry.
Key Specs to Compare
When comparing first printers, focus on these specs:
- Build volume – the maximum object size. Common sizes are 220×220×250 mm (like the Ender 3) or smaller 150×150×150 mm models.
- Auto bed leveling – sensors that compensate for an uneven bed. It saves a lot of frustration for beginners.
- Direct drive vs. Bowden extruder – direct drive pushes filament directly into the hotend, better for flexible materials; Bowden uses a tube, lighter print head.
- Heated bed – essential for ABS and helpful for PETG; PLA can print without it but it helps adhesion.
- Print speed – usually 40–60 mm/s for quality; faster speeds can reduce quality.
- Open vs. enclosed frame – enclosed is safer for ABS and reduces drafts, but open frames are easier to modify and see.
Don’t get caught up in maximum nozzle temperature or resolution numbers. For a first printer, reliability and community support matter more than raw specs.
Budget Breakdown
Your total cost is more than the printer itself. Plan for:
- Printer: $150–$500 (FDM) or $200–$400 (resin starter kits).
- Filament: $20–$30 per 1 kg spool. A spool lasts many small prints.
- Tools: spatula, pliers, wire cutters, digital calipers – about $20–$40.
- Upgrades: spare nozzles, better build surface, enclosure – $20–$100 over time.
- Safety: fire-safe container or enclosure if printing unattended – $30–$100.
Used printers can save money but may require troubleshooting; a new printer with warranty is safer for a first timer.
Common Beginner Mistakes
Even with a good printer, beginners often run into these issues:
- Not leveling the bed properly – causes poor adhesion and failed prints. Use auto-leveling if available.
- Printing too fast – reduces quality and increases chances of failure. Start at 40 mm/s.
- Ignoring filament storage – moist filament causes bubbles and weak prints. Store in a dry bag with desiccant.
- Using the wrong nozzle temperature – each material has a range (PLA ~200–220°C, PETG ~230–250°C). Check the spool label.
- Leaving the printer unattended – even quality printers can fail and cause fire risk. Never leave it running overnight without a smoke detector nearby.
Most problems are fixable with patience. Join online communities (like the r/3Dprinting subreddit) for specific troubleshooting help.
Frequently Asked Questions
What is the best first 3D printer for under $300?
The Creality Ender 3 series (V2 or Neo) is the most common recommendation. It has a large community, tons of upgrades, and prints well after initial setup. The Anycubic Kobra series offers auto-leveling at a similar price. For a more plug-and-play experience, the Prusa Mini+ is pricier but very reliable.
Should I buy a resin printer as my first?
Only if you specifically want high-detail miniatures, dental models, or jewelry. Resin printers are messier, require washing and curing stations, and the resin is toxic. FDM is easier, cheaper, and more versatile for functional parts.
How much does it cost to run a 3D printer?
Electricity is negligible (about $0.01–$0.05 per hour). Filament is the main cost: $20–$30 per kilogram, which can last months for small prints. Maintenance (nozzles, PTFE tubes) adds maybe $20–$50 per year.
Is it hard to learn 3D printing?
There is a learning curve, but it’s manageable. You’ll need to learn slicing software (like Cura or PrusaSlicer), bed leveling, and basic troubleshooting. Most people get their first successful print within a day, but mastering quality takes weeks.
Can I print with materials other than plastic?
FDM printers can print composites (wood, metal-filled PLA), but they require hardened nozzles. There are also specialty filaments like carbon fiber nylon, but they need high temperatures and are not for beginners. Resin printers only use photopolymer resin.
How do I know what print settings to use?
Start with the manufacturer’s recommended settings printed on the filament spool. In your slicer, choose the preset for your printer and material. Then adjust layer height (0.2 mm is standard), infill (20% is good for most parts), and print speed (40–50 mm/s).
Related
Formula used
in t | Print time | min | 120 | 0 in d | Object length | mm | 100 | 0 in l | Object width | mm | 80 | 0 in h | Object height | mm | 50 | 0 out v | Filament volume | cm³ | (d * l * h) / 1000 | 2 out w | Filament weight (PLA) | g | v * 1.24 | 1 out cost | Filament cost (PLA) | USD | w * 0.03 | 2
Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work
Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.