ThisCalculator

Everyday

Charge Phone to Phone? How It Works

Updated · Standard formula, shown below

Yes, you can charge one phone from another using a USB cable (OTG) or, on some models, reverse wireless charging. This lets a phone with a full battery act as a power bank for a friend’s device or your own second phone.

What Is Phone-to-Phone Charging?

Phone-to-phone charging, also called reverse charging or power sharing, transfers electrical energy from one phone’s battery to another. The phone that supplies power is the source; the one receiving is the sink. It’s a practical backup when no wall outlet or portable charger is available.

Two main methods exist:

  • Wired (USB OTG): Uses a USB On-The-Go adapter or a USB-C to USB-C cable. Works with most Android phones that support USB host mode.
  • Wireless (Reverse Wireless Charging): Uses the phone’s internal coil to broadcast power to another Qi-compatible device placed on its back. Found on many flagships since 2019.

How Wired Phone-to-Phone Charging Works

Most modern phones use USB-C, which supports power delivery in both directions. When you connect two phones with a USB-C to USB-C cable, the phones negotiate who supplies power. The phone with the higher battery level or the one configured as the source will start charging the other.

For older micro-USB phones, you need an OTG (On-The-Go) adapter. This adapter has a micro-USB male end that plugs into the source phone, and a USB-A female port. You then connect a standard USB cable from that port to the receiving phone. The source phone must support USB host mode, which most Android phones do, but iPhones do not (without special hardware).

Some phones also have a setting called “Reverse charging” or “USB power sharing” that you must enable manually. On Samsung devices, it’s under Settings → Battery → Reverse wireless charging or via the quick settings toggle.

How Wireless Reverse Charging Works

Reverse wireless charging uses the same Qi induction standard that charges your phone on a pad. The source phone’s battery sends power to its internal coil, which creates an alternating magnetic field. The receiving phone’s coil picks up that field and converts it back into electrical current to charge its battery.

To use it:

  1. Enable “Wireless power sharing” or “Reverse wireless charging” on the source phone (usually in Settings → Battery).
  2. Place the receiving phone face-up on the back of the source phone, aligning the coils (often indicated by a small icon or outline on the phone’s back).
  3. Wait for the charging indicator on both phones.

This method is slower than wired, typically delivering 4.5W to 10W depending on the phone model. It’s best for topping up a low battery, not for a full charge.

How to Choose the Right Method

Consider these factors:

  • Speed: Wired is faster. A USB-C to USB-C cable can deliver 15W-27W or more, while wireless tops out around 10W.
  • Compatibility: Wired works with any phone that has USB-C and supports OTG. Wireless requires both phones to have Qi coils.
  • Battery drain: The source phone loses battery at roughly 1.5 to 2 times the rate the receiver gains it, due to conversion losses. For example, if you transfer 10% to the other phone, you might lose 15-20% from your own.
  • Cable quality: A cheap or damaged cable can cause slow charging or no connection. Use a cable rated for at least 3A if possible.

Common Problems and Misconceptions

“My phone charges the other but not vice versa.” This is normal. Many phones only support one direction. Check the source phone’s manual for “USB power sharing” or “OTG charging.”

“It’s not working with an iPhone.” iPhones do not support USB host mode for charging another phone via cable. However, iPhone 15 and later models support reverse wireless charging (up to 4.5W) to charge AirPods or an Apple Watch, but not another iPhone (they refuse due to power negotiation).

“The source phone gets hot.” Heat is normal during power transfer. If it gets uncomfortably hot, stop charging and let it cool.

“It’s draining my phone too fast.” The source phone will drain faster than the receiver gains. This is expected due to inefficiency.

Safety and Battery Health

Phone-to-phone charging is safe when used occasionally and with compatible devices. However, keep these points in mind:

  • Do not use it as a primary charging method. The source phone’s battery cycles faster, which can shorten its lifespan over time.
  • Monitor heat. If either phone becomes very hot, disconnect immediately.
  • Use only official or certified cables and adapters. Non-certified ones may not negotiate power correctly, leading to slow charging or damage.
  • Do not charge a phone from another while both are in a pocket or bag; the heat has no place to dissipate.
  • For wireless reverse charging, remove thick cases or metal objects (like pop sockets) that can interfere with the magnetic field.

Alternatives to Phone-to-Phone Charging

If you don’t have a second phone or want a more efficient solution, consider:

  • Portable power bank: A dedicated battery pack with 10,000mAh can charge a phone 2-3 times and is more efficient than using another phone.
  • Wall charger: The fastest and most reliable option when an outlet is available.
  • Solar charger: Useful for outdoor trips, though slow and weather-dependent.
  • Car charger: If you’re in a vehicle, a 12V adapter is better than draining a phone.

Frequently Asked Questions

Can I charge my iPhone from an Android phone?

Yes, but only via wired USB-C to Lightning (or USB-C to USB-C on iPhone 15 and later) if the Android phone supports OTG. The Android phone will act as the power source. Wireless reverse charging from Android to iPhone works only if the iPhone is placed on the Android’s back, but the iPhone will charge very slowly (around 5W).

Does phone-to-phone charging damage either battery?

Occasional use is fine. However, the source phone’s battery will undergo more charge/discharge cycles, which can accelerate aging if done frequently. The receiving phone is charged normally, so no extra wear.

How fast is phone-to-phone charging?

Wired USB-C to USB-C can deliver 15W-27W, which is similar to a wall charger. Wireless reverse charging is slower, typically 4.5W-10W, so it might take 3-4 hours to fully charge a modern phone.

Why does my phone not support reverse wireless charging?

Reverse wireless charging requires a specific hardware coil and power management IC. Many mid-range and budget phones omit it to save cost. Check your phone’s spec sheet for “reverse wireless charging” or “power sharing.”

Can I charge a smartwatch or earbuds from my phone?

Yes, if they support Qi wireless charging. Many modern earbuds (like AirPods or Samsung Galaxy Buds) and smartwatches can be charged by placing them on the back of a phone that supports reverse wireless charging. Wired is not possible without special adapters.

What is the maximum distance for wireless phone-to-phone charging?

Qi wireless charging requires the coils to be almost touching, typically within 5mm. You must place the phones directly back-to-back. There is no “over the air” charging for consumer phones yet.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.