ThisCalculator

Everyday

Bosch DFM064W50A Specs, Cabinet Fit & Filter Care

Updated · Standard formula, shown below

Bosch DFM064W50A Specs, Cabinet Fit & Filter Care

This article covers the Bosch DFM064W50A range hood’s key specifications, how to check if it fits your cabinet setup, and how to clean or replace its filters. You’ll get the exact dimensions, installation requirements, and step-by-step filter maintenance instructions.

Key Specifications at a Glance

The Bosch DFM064W50A is a 60 cm wide under-cabinet range hood designed for ducted or recirculating extraction. Its main specs are:

  • Width: 60 cm (fits standard 60 cm cabinets)
  • Depth: 31.5 cm
  • Height: 12.5 cm (without chimney extension)
  • Max airflow: 400 m³/h (ducted mode)
  • Noise level: 54–68 dB depending on speed
  • Controls: Mechanical push buttons, 3 speeds plus intensive
  • Lighting: 2× 3 W LED
  • Filter: Aluminum mesh, washable

It uses a 150 mm exhaust duct (also works with 125 mm with an adapter). For recirculating mode, you need an optional carbon filter (e.g., Bosch DKF70).

Cabinet Fit: What You Need to Measure

Before buying, measure your cabinet’s internal width, depth, and height. The DFM064W50A fits under a standard 60 cm wall cabinet, but you must verify:

  • Internal width: At least 56 cm (the hood’s body is 60 cm wide, but the mounting brackets need about 2 cm on each side).
  • Internal depth: At least 31.5 cm, but ideally 32–33 cm so the hood doesn’t protrude awkwardly.
  • Height clearance: The hood is 12.5 cm tall. If your cabinet base is higher, you’ll need a filler strip or install lower.

Also check that the duct outlet (top or back) aligns with your duct path. The hood can vent through the top or rear; if you’re recirculating, the outlet is covered by a charcoal filter.

How the Hood Works: Ducted vs. Recirculating

The DFM064W50A can operate in two modes:

  • Ducted (exhaust to outside): Air is pulled through the aluminum mesh filter, then through a duct to the outside. This is more efficient at removing grease and odors.
  • Recirculating (carbon filter): Air passes through the mesh filter, then a charcoal filter that absorbs odors, and is released back into the kitchen. This is for kitchens without an external vent.

In recirculating mode, the carbon filter must be replaced every 3–6 months depending on cooking frequency. The aluminum mesh filter should be cleaned monthly.

Filter Care: Cleaning and Replacement

Proper filter maintenance keeps the hood efficient and prevents grease buildup. Here’s how:

  1. Remove the mesh filter: Push the spring-loaded handle toward the back and pull down. It slides out easily.
  2. Clean the mesh filter: Wash by hand in hot soapy water, or in the dishwasher (place upright). Do not use harsh abrasives. Let it dry completely before reinstalling.
  3. Replace carbon filter (if recirculating): Remove the mesh filter, then the carbon filter sits behind it. Unclip and replace with a new one (Bosch DKF70).
  4. Reinstall: Slide the mesh filter back into place until it clicks. Make sure it’s fully seated.

If the filter is damaged or deformed, replace it. A clogged filter reduces airflow and increases noise.

Common Problems and Troubleshooting

Here are typical issues and solutions:

  • Hood doesn’t turn on: Check the power cord, circuit breaker, and that the plug is fully inserted.
  • Reduced airflow: Clean or replace the filters, check the duct for blockages, and ensure the damper flap opens.
  • Loud noise: Often due to loose duct connections or a clogged filter. Tighten connections and clean filters.
  • Lights not working: The LED units may need replacement; contact a service technician.

Installation Considerations

Installation should be done by a qualified person. Key points:

  • Height above cooktop: Minimum 65 cm for electric, 75 cm for gas (check local codes).
  • Ducting: Use rigid or flexible metal duct. Keep it short and straight; each bend reduces efficiency.
  • Electrical: The hood requires a 220–240 V supply. Ensure the outlet is accessible after installation.

If you’re replacing an older hood, the mounting holes may not align—use the provided template to mark new holes.

Comparing with Other Bosch Models

The DFM064W50A is a mid-range under-cabinet hood. Compared to the DFM062W50 (similar but lower airflow), the DFM064 offers higher extraction (400 vs. 340 m³/h). The DFM064 also has an intensive speed setting for quick steam removal. If you have a larger kitchen, consider a wall-mounted or island hood with higher airflow.

Frequently Asked Questions

Does the Bosch DFM064W50A come with a carbon filter?

No, the carbon filter is not included. You need to purchase it separately (Bosch DKF70) if you use recirculating mode.

Can I install this hood over an island?

No, it’s designed for under-cabinet installation. For an island, you need a ceiling-mounted hood.

How often should I clean the aluminum mesh filter?

Ideally once a month, but if you cook frequently with oil, clean it every two weeks. A clogged filter reduces performance.

What is the warranty on this hood?

Bosch typically offers a 2-year manufacturer warranty, but check your local dealer for exact terms.

Can I use a 125 mm duct instead of 150 mm?

Yes, with a reducing adapter, but airflow will be reduced. Use 150 mm if possible for best performance.

Related

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.