ThisCalculator

Math

Area of a Circle: Formula & Calculator

Updated · Standard formula, shown below

Area (from radius) 78.54 m²
Area (from diameter)
78.54 m²
Result
Area (from circumference)
78.56 m²
Result
Radius
5 m
You entered

This calculator works out the area of a circle from its radius, diameter, or circumference. You enter one known measurement, and you get the area in square units (like cm², m², or in²) instantly. The formula used is the standard A = πr², and the calculator also shows the result for the other two measurements so you can check your own work.

Formula

The area of a circle is the number of square units that fit inside the circle. The standard formula is:

A = π × r²

  • A = area (in square units, e.g., m², cm², in²)
  • π (pi) ≈ 3.14159… (a constant)
  • r = radius (the distance from the center to the edge, in the same unit)

If you know the diameter (d = 2r), the formula becomes A = π × (d/2)². If you know the circumference (C = 2πr), you can use A = C² / (4π). All three are equivalent.

Worked Example

Using the default values from the calculator above (radius = 5 m):

  1. Write the formula: A = π × r²
  2. Plug in the radius: A = π × (5)²
  3. Square the radius: 5² = 25
  4. Multiply by π: A = 3.14159 × 25 = 78.53975…
  5. Round to 2 decimal places: A ≈ 78.54 m²

The calculator’s first output shows 78.54 m², matching this result. If you instead enter a diameter of 10 m, you get the same area because the radius is half the diameter.

When to Use This Calculator

You need the area of a circle whenever you’re working with round objects or spaces: a circular garden, a pizza, a pipe’s cross-section, a round tablecloth, or a circular pond. It’s also a building block in many geometry and physics problems (e.g., volume of a cylinder = area × height).

In real life, you often measure the diameter (e.g., a round table’s width) or the circumference (e.g., wrapping a tape measure around a tree trunk). This calculator accepts any of the three so you don’t have to convert first.

How to Read the Result

The area is always in square units. If you entered meters, the area is in square meters (m²). If you entered inches, it’s in square inches (in²). This is because you multiplied two lengths together (radius × radius).

For example, a circle with a radius of 2 cm has an area of about 12.57 cm². That means you could fit 12.57 one-centimeter squares inside the circle (approximately, because the edge is curved).

If you need the area in a different unit, convert the radius first, then compute. For instance, to get square feet, enter the radius in feet. The calculator does not convert units for you.

Common Mistakes and How to Avoid Them

  • Using the diameter instead of the radius. This is the most common error. The formula uses r, not d. If you have the diameter, halve it first (or use the diameter input in the calculator).
  • Forgetting to square the radius. Many people multiply π × r instead of π × r². For a radius of 5, π × 5 = 15.7, but the correct area is 78.54.
  • Unit mix-ups. If you measure the radius in inches but want area in square feet, you must convert inches to feet first (divide by 12) before squaring. Otherwise you get square inches.
  • Rounding too early. If you round π to 3.14, you get a slightly different result (e.g., 78.5 vs. 78.54). For most purposes, 3.14 is fine, but for exact work use the π button on a calculator.

Limits of the Formula

The formula A = πr² assumes a perfect, flat circle. Real-world objects are rarely perfect: a tree trunk is not a perfect circle, a pizza might be slightly oval, and a pipe’s cross-section might be elliptical. In those cases, the formula gives an approximation. For very large circles (like the Earth’s equator), the curvature of the sphere matters, but for everyday objects, the error is negligible.

Also, the formula gives the area of the surface enclosed by the circle, not the area of a sphere’s surface. If you need the surface area of a ball, use 4πr².

Frequently Asked Questions

Why is the area of a circle πr²?

Imagine cutting a circle into many thin wedges and rearranging them into a rectangle. The width of that rectangle is the radius (r), and the length is half the circumference (πr). Area = length × width = πr × r = πr². This is a visual proof, not a formal one, but it shows why the constant π appears.

Can I calculate the area if I only know the circumference?

Yes. Use the formula A = C² / (4π). For example, if the circumference is 31.42 m, then A = (31.42)² / (4π) ≈ 987.2 / 12.566 ≈ 78.54 m². The calculator’s third output does exactly this.

What if I only know the diameter?

Use A = π × (d/2)². For a diameter of 10 m, that’s π × 5² = 78.54 m². The calculator’s second output shows this.

Is the area always in square units?

Yes. Area is a two-dimensional measure, so the unit is always squared. If you enter centimeters, you get cm²; if you enter feet, you get ft².

How do I find the radius if I know the area?

Rearrange the formula: r = √(A/π). For example, if the area is 78.54 m², then r = √(78.54/π) ≈ √(25) = 5 m.

Does the formula work for a semi-circle?

For a semi-circle, calculate the full circle’s area and then divide by 2. For a quarter-circle, divide by 4. The same formula applies; you just take a fraction of the result.

Related

Formula used
in r | Radius | m | 5 | 0
in d | Diameter | m | 10 | 0
in c | Circumference | m | 31.42 | 0
out area_r | Area (from radius) | m² | pi * r^2 | 2
out area_d | Area (from diameter) | m² | pi * (d/2)^2 | 2
out area_c | Area (from circumference) | m² | c^2 / (4*pi) | 2

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.